K3020P, K3020PG Series
www.vishay.com
Vishay Semiconductors
Rev. 2.4, 30-Aug-16
2
Document Number: 83505
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
Notes
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
(1)
Test voltage must be applied within dV/dt ratings.
(2)
I
FT
is defined as a minimum trigger current.
ABSOLUTE MAXIMUM RATINGS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
INPUT
Reverse voltage V
R
5V
Forward current I
F
80 mA
Surge current P.W. < 10 μs I
FSM
3A
Power dissipation P
diss
100 mW
Junction temperature T
j
100 °C
OUTPUT
Peak off-state voltage V
DRM
400 V
On-state RMS current I
D(RMS)
100 mA
Peak surge current t
p
10 ms I
FSM
1.5 A
Power dissipation P
diss
300 mW
Junction temperature T
j
100 °C
COUPLER
Total power dissipation P
tot
350 mW
Storage temperature range T
stg
-55 to +150 °C
Ambient temperature T
amb
-55 to +100 °C
Junction temperature T
j
100 °C
Lead soldering temperature 2 mm from case, t < 10 s T
sld
260 °C
ELECTRICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT
INPUT
Forward voltage I
F
= 50 mA V
F
-1.31.6V
Reverse voltage I
R
= 10 μA V
R
5--V
Junction capacitance V
R
= 0 V, f = 1 MHz C
j
-50-pF
OUTPUT
Forward peak off-state voltage
(repetitive)
I
DRM
= 100 nA V
DRM
(1)
400 - - V
Peak on-state voltage I
TM
= 100 mA V
TM
-1.53 V
Critical rate of rise of off-state
voltage
I
F
= 0 A, V
D
= 0.67 V
DRM
dV/dt
cr
-10-V/μs
Critical rate of rise of on-state
current commutation
V
D
= 30 V
RMS
, I
D
= 15 mA
RMS
dV/dt
crq
0.1 0.15 - V/μs
COUPLER
(2)
Emitting diode trigger current V
S
= 3 V, R
L
= 150
K3020P I
FT
-1530mA
K3020PG I
FT
-1530mA
K3021P I
FT
-815mA
K3021PG I
FT
-815mA
K3022P I
FT
-510mA
K3022PG I
FT
-510mA
K3023P I
FT
-35mA
K3023PG I
FT
-35mA
Holding current I
F
= 10 mA, V
S
3 V I
H
- 200 - μA
