OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HHT272P030HL0

P1-P3P4-P5
Specications
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Type HHT 175 °C, Aluminum Electrolytic Capacitor
Type HHT has long life and rugged construction for high temperature
environments. HHT capacitors are rated for full operating voltage at
175 °C and tested to 2000 hrs at rated voltage and temperature. 5000
hours of life at 150 ºC with ripple current ratings up to 10 Arms.
Highlights
- Rated for +175 ºC without voltage derating
- High capacitance retention @ -40 ºC
- Up to 20g vibration
Temperature Range –40 °C to +175 °C
Rated Voltage Range 16 Vdc to 40 Vdc
Capacitance Range 470 µF to 4700 µF
Capacitance Tolerance –10 / +30%
Leakage Current (at 20 ºC) I = 0.003 CV +4.0 µA; after 5 minutes at rated voltage
I = leakage current in µAmps
C = rated capacitance in µF
V = rated DC Working voltage in Volts
Ripple Current vs. Frequency Correction Factors
Low Temperature Characteristics Impedance ratio: Z
–40 ⁰C
∕ Z
+25 ⁰C
@120 Hz ≤3
DC Life Test 2000 h @ rated voltage at 175 °C
∆ Capacitance 30V and 40V ±20% , 16V ±25%
ESR 200% of limit
DCL 100% of limit
Shelf Life Test (+105 ºC/0 Vdc): 1000 hours
(+40 ºC/0 Vdc): 10 years
Case Material Stainless Steel
Frequency (Hz) 100 300 1000 5000 100 kHz
Ripple Current Correction Factor 0.35 0.57 0.8 1 1.04
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Part Numbering System
Vibration Test Mil standard 202, method 204, high frequency 20g’s
Surge Voltage Test Subject the capacitors to their rated surge voltage at normal room temperature
and through a 1000 Ω ±10% resistor (except for capacitances of 2500 µF and
up, use a higher value resistor calculated as 2,500,000/C Ω ±10% where C is
the capacitance in µF). Cycle the voltage ½ minute on followed by 4½ minutes
o during which each capacitor is discharged through the charging resistor or
equal resistor. Repeat the cycles for 120 h. Post test requirements are for DCL,
ESR and DF to meet initial requirements and for there to be no evidence of
mechanical damage or electrolyte leakage.
Storage at Low Temperature Test Test
Subject the capacitor to 72 hours at -55°C. After 16 hours at room temperature, measure
the capacitance and DCL.
∆C
Capacitance change from the initial measurement must not exceed 10%.
DCL
Leakage current will meet the initial specication.
Appearance
No electrolyte leakage or other visible damage. The markings are to be legible.
Type HHT 175 °C, Aluminum Electrolytic Capacitor
HHT 332 P 016 H J 0
Type Capacitance Tolerance Rated Voltage Case Diameter Case Length Code Sleeve/Label
HHT 332 =3300 µF
471 = 470 µF
P = -10/+30% 016 = 16 Vdc
030 = 30 Vdc
040 = 40 Vdc
H = 22mm E = 37mm
J = 45mm
L = 53mm
0 = Label
1 = Sleeve
Outline Drawing
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Ratings
Cap
(µF)
120Hz
25 ˚C
Case Size
D x L mm
ESR max
Ripple (A)
Voltage
Catalog Part Number
25 °C (mΩ) 150 °C Ambient
120 Hz 5 Khz
16 Vdc @ 175 °C
25 Vdc Surge @25 °C
2200
3300
4700
HHT222P016HE0
HHT332P016HJ0
HHT472P016HL0
22 x 37
22 x 45
22 x 53
90
60
42
7.1
8.9
10.3
30 Vdc @ 175 °C
40 Vdc Surge @25 °C
1500
2200
2700
HHT152P030HE0
HHT222P030HJ0
HHT272P030HL0
22 x 37
22 x 45
22 x 53
133
90
74
7.3
8.9
10.1
40 Vdc @ 175°C
63 Vdc Surge @25°C
470
680
900
HHT471P040HE0
HHT681P040HJ0
HHT901P040HL0
22 x 37
22 x 45
22 x 53
423
293
221
5.5
6.9
8.1
Type HHT 175 °C, Aluminum Electrolytic Capacitor
Typical
Weight
HE = 43 g
HJ = 50 g
HL = 56 g
22.2mm±0.2
"L"±.25mm
"L"+5.0mm
28mm MIN
Both Sides
2.2mm
Both Sides
1.02mm DIA, 18 AWG LEADS
(TYP)
P1-P3P4-P5

HHT272P030HL0

Mfr. #:
Buy HHT272P030HL0
Manufacturer:
Cornell Dubilier (CDE)
Description:
Aluminum Electrolytic Capacitors - Axial Leaded 2700uF -10 / +30% 30 Volts
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet