PLN-100-27 Datasheet PLN-100-36, PLN-100-48, PLN-100-15 | P1-P3

THD< 20% when output loading≧75% at 115VAC/230VAC input and output loading≧75% at 277VAC input

TOTAL HARMONIC DISTORTION

MAX. No. of PSUs on 16A

CIRCUIT BREAKER

3 units (circuit breaker of type B) / 5 units (circuit breaker of type C) at 230VAC

SPECIFICATION

MODEL PLN-100-12 PLN-100-15 PLN-100-20 PLN-100-24 PLN-100-27 PLN-100-36 PLN-100-48

DC VOLTAGE

RATED CURRENT Note.5

RATED POWER Note.5

OUTPUT

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE Note.4

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

AC CURRENT (Typ.)

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

SAFETY STANDARDS Note.7

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVER CURRENT

OVER VOLTAGE

OVER TEMPERATURE

12V 15V 20V 24V 27V 36V 48V

5A 5A 4.8A 4A 3.55A 2.65A 2A

60W 75W 96W 96W 95.85W 95.4W 96W

150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 200mVp-p

±3.0%

±1.0%

±2.0%

500ms, 80ms/230VAC 1200ms, 80ms/115VAC at full load

60ms/230VAC 16ms/115VAC at full load

90 ~ 295VAC 127 ~ 417VDC

47 ~ 63Hz

PF>0.95/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

±3.0% ±3.0% ±3.0% ±3.0% ±2.0% ±2.0%

13 ~ 16V 16.5 ~ 20V 22 ~ 27V 27 ~ 34V 30 ~ 36V 39 ~ 48V 52 ~ 64V

COLD START 40A(twidth=1030 s measured at 50% Ipeak) at 230VACμ

<0.75mA / 240VAC

95 ~ 102%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH

-30 ~ +50℃ (Refer to "Derating Curve")

20 ~ 95% RH non-condensing

-40 ~ +80℃, 10 ~ 95% RH

±0.03%/℃ (0 ~ 50℃)

10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes

303.1Khrs min. MIL-HDBK-217F (25℃)

200*70.5*35mm (L*W*H)

0.52Kg; 20pcs/12.5Kg/0.9CUFT

Protection type : Shut down and latch off o/p voltage, re-power on to recover

100W Single Output Switching Power Supply

‧UniversalACinput/Fullrange(upto295VAC)

‧Highefficiencyupto88.5%

‧Protections:Shortcircuit/Overcurrent/Overvoltage/Overtemperature

‧Coolingbyfreeairconvection

‧Built-inactivePFCfunction

‧FullyisolatedplasticcasewithIP64level

‧PassLPS

‧Class2powerunit

‧100%fullloadburn-intest

‧Highreliability

‧SuitableforLEDlightingandmovingsignapplications

‧Suitablefordry/damplocations

‧Compliancetoworldwidesafetyregulationsforlighting

‧2yearswarranty

■Features:

PLN-100 series

RIPPLE & NOISE (max.) Note.2

VOLTAGE TOLERANCE Note.3

ENVIRONMENT

SAFETY &

EMC

PROTECTION

Shut down o/p voltage, re-power on to recover

Compliance to EN55015, EN55032 (CISPR32) Class B, EN61000-3-2 Class C (>75% load) ; EN61000-3-3;GB17743 and GB17625.1,EAC TP TC 020

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A;EAC TP TC 020

IP64

M M

110

LPS

SELV

9 ~ 12V 11.25 ~ 15V 15 ~ 20V 18 ~ 24V 20.25 ~ 27V 27 ~ 36V 36 ~ 48V

CONSTANT CURRENT REGION Note.6

SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed

VOLTAGE ADJ. RANGE (SVR1)

CURRENT ADJ. RANGE(SVR2)

10.2 ~ 12V

3.75 ~ 5A

12.8 ~ 15V

3.75 ~ 5A

17 ~ 20V

3.6 ~ 4.8A

20.4 ~ 24V

3 ~ 4A

23 ~ 27V

2.6 ~ 3.55A

30.6 ~ 36V

2 ~ 2.65A

40.8 ~ 48V

1.5 ~ 2A

EMC IMMUNITY

EMC EMISSION

83% 85% 88.5% 88.5% 88% 88% 88.5%

12V:0.8A/115VAC 0.4A/230VAC 0.3A/277VAC 15V:0.9A/115VAC 0.45A/230VAC 0.35A/277VAC

20V ~ 48V:1.1A/115VAC 0.55A/230VAC 0.45A/277VAC

1.AllparametersNOTspeciallymentionedaremeasuredat230VACinput,ratedloadand25℃ofambienttemperature.

2.Ripple&noisearemeasuredat20MHzofbandwidthbyusinga12"twistedpair-wireterminatedwitha0.1uf&47ufparallelcapacitor.

3.Tolerance:includessetuptolerance,lineregulationandloadregulation.

4.Deratingmaybeneededunderlowinputvoltage.Pleasecheckthestaticcharacteristicsformoredetails.

5.Thisisthemaximumpossibleoutputcurrentandpower.Overloadprotectionmaybeactivatedslightlybelowthisleveltocomplywiththerequirement

ofUL1310class2.

6.Pleasereferto"DRIVINGMETHODSOFLEDMODULE".

7.SafetyandEMCdesignrefertoEN60598-1,subject8750(UL),CNS15233,GB7000.1,FCCpart18.

8.Thepowersupplyisconsideredasacomponentthatwillbeoperatedincombinationwithfinalequipment.SinceEMCperformancewillbeaffectedbythe

completeinstallation,thefinalequipmentmanufacturersmustre-qualifyEMCDirectiveonthecompleteinstallationagain.

9.TofulfillrequirementsofthelatestErPregulationforlightingfixtures,thisLEDpowersupplycanonlybeusedbehindaswitchwithoutpermanently

connectedtothemains.

10.Theambienttemperaturederatingof3.5℃/1000mwithfanlessmodelsandof5℃/1000mwithfanmodelsforoperatingaltitudehigherthan2000m(6500ft).

File Name:PLN-100-SPEC 2018-06-07

UL879, UL1310, UL8750, CSA C22.2 No. 207-M89, TUV EN61347-1, EN61347-2-13 independent, TUV EN60950-1,CAN/CSA C22.2 No.223-M91(except for 48V),

CAN/CSA C22.2 No. 250.13-12, EAC TP TC 004,GB19510.1,GB19510.14,IP64, J61347-1, J61347-2-13 approved ; design refer to UL60950.

(exceptfor48V)forUL1310

(allmodels)forUL8750andUL879

(for48Vonly)

(CCCoptional)

230VAC

Input only

Mechanical Specification

Case No.955A Unit:mm

Fosc : 100KHz

Derating Curve Static Characteristics

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V) 60Hz

Block Diagram

DETECTION

PWM & PFC

CIRCUIT

O.L.P.

EMI FILTER

RECTIFIERS

POWER

SWITCHING

FILTER

RECTIFIERS

-V

I/P

CONTROL

O.V.P.

O.L.P.

PFC

CIRCUIT

PFC

CONTROL

(HORIZONTAL)

LOAD (%)

-30 -25 -10 0 15 30 40 50

100

90 100 125 135 145 155 165 175 180 200 230 295

100

LOAD (%)

100

T case

35.25

※ T case: Max. Case Temperature.

100W Single Output Switching Power Supply

PL N -1 0 0 ser i e s

310±20

6.26

200

SVT 18AWG×2C

22.84

70.5

SVT 18AWG×3C

2-R2.5

+V(Red)

-V(Black)

310±20

FG (Green/Yellow)

AC/L(Brown)

AC/N(Blue)

SVR2

SVR1

Output voltage and current adjustment : remove the upper case and adjust through SVR1 & SVR2

shown in the diagram.

Output voltage adjustment

Output current adjustment

SVR1

SVR2

File Name:PLN-100-SPEC 2018-06-07

0.76

0.78

0.80

0.82

0.84

0.86

0.88

0.90

0.92

0.94

0.96

0.98

1.00

50% 60% 70% 80% 90% 100%

115V

230V

277V

10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

115V

230V

277V

PLN-100 series possess superior working efficiency that up to 88.5% can be reached in field applications.

EFFICIENCY (%)

LOAD

Power Factor Characteristic

EFFICIENCY vs LOAD (48V Model)

Constant Current Mode

LOAD

There are two major kinds of LED drive method "direct drive" and "with LED driver".

A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs.

Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)].

DRIVING METHODS OF LED MODULE

100W Single Output Switching Power Supply

PL N -1 0 0 ser i e s

(100W)

Typical LED power supply I-V curve

Vo(%)

100

50 100

(min.)

Io (%)

Constant

Current area

Hiccup

Protection

Constant

Voltage area

(A)

(B)

(C)

In the constant current region, the highest voltage at the output of the driver

depends on the configuration of the end systems.

Should there be any compatibility issues, please contact MEAN WELL.

File Name:PLN-100-SPEC 2018-06-07

P1-P3

PLN-100-27

Mfr. #:

Buy PLN-100-27

Manufacturer:

MEAN WELL

Description:

LED Power Supplies 27V 3.55A 95.85W Active PFC Function

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

PLN-100-27

PLN-100-27

Products related to this Datasheet