PTV12010WAH Datasheet PTV12010WAH, PTV12010LAD | P1-P3

DC-DC CONVERTERS POLA Non-isolated 1

NEW Product

File Name: ptv12010w.pdf Rev (02): 19 Dec 2005

2 YEAR WARRANTY

All specifications are typical at nominal input, full load at 25 °C unless otherwise stated

= 100 µF and 10 µF (Ceramic), C

out

= 0 µF

SPECIFICATIONS

*Auto-track™ is a trade mark of

Texas Instruments

The PTV12010 is a non-isolated dc-dc converter from Artesyn under the Point of Load

Alliance (POLA) standard. The vertical mounting option of the PTV12010 module provides

performance in less than 20% of the space that is required by alternative solutions. The

Auto-Track™ feature provides for sequencing between multiple modules, a function,

which is becoming a necessity for powering advanced silicon including DSP’s, FPGA’s

and ASIC’s requiring controlled power-up and power-down. The PTV12010 has an input

voltage of 10.8 Vdc to 13.2 Vdc and offers a wide 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and

0.8 Vdc to 1.8 Vdc for suffix ‘L’ output voltage range with up to 8 A output current, which

allows for maximum design flexibility and a pathway for future upgrades.

• 8 A output current

• 1

2 V input voltage

• Wide-output voltage adjust

• 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and

0.8 Vdc to 1.8 Vdc for suffix ‘L’

• Auto-track™ sequencing*

• Pre-bias start-up

• Efficiencies up to 93%

• Output ON/OFF inhibit

• Vertical through-hole mounting

• Point-of-Load-Alliance (POLA) compatible

• Undervoltage lockout

• Available RoHS compliant

PTV12010

12 Vin single output

OUTPUT SPECIFICATIONS

Voltage adjustability Suffix ‘W’ 1.2-5.5 Vdc

(See Note 4) Suffix ‘L’ 0.8-1.8 Vdc

Setpoint accuracy (See Note 8) ±2.0% Vo

Line regulation ±10 mV typ.

Load regulation ±12 mV typ.

Total regulation (See Note 8) ±3.0% Vo

Minimum load

0 A

Ripple and noise Suffix ‘W’ 20 mV pk-pk

20 MHz bandwidth Suffix ‘L’ 15 mV pk-pk

Temperature co-efficient -40 ºC to +85 ºC ±0.5% Vo

ransient response 70 µs recovery time

(See Note 5)

Overshoot/undershoot 100 mV

INPUT SPECIFICATIONS

Input voltage range (See Note 3) 10.8V-13.2 Vdc

Input standby current 10 mA typ.

Remote ON/OFF (See Note 1) Positive logic

Undervoltage lockout (Increasing) 9.5 V typ.

Track input current Pin 5 (See Notes 6 and 7) -0.13 mA

International Safety Standard Approvals

UL/cUL CAN/CSA-C22.2 No. 60950

File No. E174104

TÜV Product Service (EN60950) Certificate No. B 04 06 38572 044

CB Report and Certificate to IEC60950, Certificate No.

US/8292/UL

EMC CHARACTERISTICS

Electrostatic discharge EN61000-4-2, IEC801-2

Conducted immunity EN61000-4-6

Radiated immunity EN61000-4-3

GENERAL SPECIFICATIONS

Efficiency See Tables on page 2

Insulation voltage Non-isolated

Switching fr

equency

Suffix ‘W’ 250-400 kHz 325 kHz typ.

Suffix ‘L’ 200-300 kHz 250 kHz typ.

Approvals and EN60950

standar

UL/cUL60950

Material flammability

UL94V

-0

Dimensions (L x W x H) 22.86 x 8.38 x 10.16 mm

0.90 x 0.330 x 0.400 in

Weight 2.6 g (0.09 oz)

MTBF Telcordia SR-332 5,000,000 hours

ENVIRONMENTAL SPECIFICATIONS

Thermal performance Operating ambient, -40 ºC to +85 ºC

(See Note 2) temperature

Non-operating -40 ºC to +125 ºC

PROTECTION

Over

cur

ent

Auto reset 16 A typ.

File Name: ptv12010w.pdf Rev (02): 19 Dec 2005

For the most current data and application support visit www.artesyn.com/powergroup/products.htm

DC-DC CONVERTERS POLA Non-isolated 2

NEW Product

PTV12010

12 Vin single output

Part Number System with Options

Product Family

Point of Load Alliance

Compatible

Mounting V

ersion

V = Vertical

Mounting Style

(9)

= Horizontal Through-Hole (Matte Sn)

H = Horizontal Through-Hole (Sn/Pb)

The ultra-wide output voltage trim range offers major advantages to users who

select the PTV12010. It is no longer necessary to purchase a variety of

modules in order to cover different output voltages. The output voltage can be

trimmed in a range of 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc

for suffix ‘L’. When the PTV12010 converter leaves the factory the output has

been adjusted to the default voltage of 1.2 V for the PTV12010W and 0.8 V for

PTV12010L.

OOuuttppuutt VVoollttaaggee AAddjjuussttmmeenntt ooff tthhee PPTTVV1122001100 SSeerriieess

Output Current

01 = 8 A

Input Voltage

12 = 12 V

Mechanical Package

Always 0

PTV12010WAH

Pin Style

A = Through-Hole Std. Pin Length (0.150”)

Output Voltage Code

W = Wide

L = Low Voltage

EFFICIENCY T

ABLE - PTV12010L (I

= I

OMAX

)

OUTPUT VOLTAGE EFFICIENCY

Vo = 1.8 V 87%

Vo = 1.5 V 86%

Vo = 1.2 V 84%

o = 1.0 V

81%

Vo = 0.8 V 78%

EFFICIENCY T

ABLE - PTV12010W

= I

OMAX

)

OUTPUT VOLTAGE EFFICIENCY

Vo = 5.0 V 92%

Vo = 3.3 V 90%

Vo = 2.5 V 88%

o = 1.8 V

85%

Vo = 1.5 V 83%

Vo = 1.2 V 80%

NNootteess

1 Remote ON/OFF

. Positive logic

ON:

Pin 7 open; or V > 2 V

OFF: Pin 7 GND; or V < 0.6 V

2 See Figures 1, 2, 3 and 6 for safe operating curves.

3 A 100 µF electrolytic input capacitor is required for proper operation as

well as a 10 µF high-frequency ceramic capacitor. The electrolytic

capacitor must be rated for the minimum rms of ripple current.

4 An external output capacitor is not required for basic operation. Adding

100 µF of distributed capacitance at the load will improve the transient

esponse.

5 1 A/

s load step, 50 to 100% I

omax

, C3 = 100

6 If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).

7 The pre-bias start-up feature is not compatible with Auto-Track™. This is

because when the module is under Auto-Track™ control, it is fully active

and will sink current if the output voltage is below that of a back-feeding

sour

ce. Therefore to ensure a pre-bias hold-off, one of the following two

techniques must be followed when input power is first applied to the

module. The Auto-Track™ function must either be disabled, or the

module’s output held off using the Inhibit pin. Refer to Application Note

196 for more details.

8 The set-point voltage tolerance is af

fected by the tolerance and stability

of R

set

. The stated limit is unconditionally met if R

set

has a tolerance of

1% with 100/

ºC or better temperature stability.

9 To order Pb-free (RoHS compatible) through-hole parts replace the

mounting option ‘H’ with ‘D’, e.g. PTV12010WAD.

10 NOTICE: Some models do not support all options. Please contact your

local Artesyn representative or use the on-line model number search tool at

http://www

.ar

tesyn.com/power

oup/pr

oducts.htm to find a suitable

alternative.

OUTPUT

INPUT OUTPUT

OUTPUT OUTPUT

EFFICIENCY

REGULATION

MODEL

POWER

VOLTAGE VOLTAGE

CURRENT CURRENT

(MAX.)

LINE LOAD

NUMBER

(9,10)

(MAX.) (MIN.) (MAX.)

(2)

15 W 10.8-13.2 Vdc 0.8-1.8 Vdc 0 A 8 A 87% ±10 mV ±12 mV PTV12010L

44 W 10.8-13.2 Vdc 1.2-5.5 Vdc 0 A 8 A 92% ±10 mV ±12 mV PTV12010W

File Name: ptv12010w.pdf Rev (02): 19 Dec 2005

For the most current data and application support visit www.artesyn.com/powergroup/products.htm

C-DC CONVERTERS POLA Non-isolated 3

NEW Product

TEMPERATURE (ºC)

Nat conv

00 LFM

400 LFM

OUTPUT CURRENT (A)

012345678

TEMPERATURE (ºC)

OUTPUT CURRENT (A)

0123456

at conv

00 LFM

Figure 2 - Safe Operating Area

Vin = 12 V

, Output Voltage = 3.3 V (See Note A)

Figure 1 - Safe Operating Area

Vin = 12 V

, Output Voltage = 5 V (See Note A)

EFFICIENCY (%)

OUTPUT CURRENT (A)

5.0V

3.3V

1.8V

1.2V

100

02 6

Vout

Figur

e 4 - Efficiency vs Load Current

in = 12 V (See Note B)

TEMPERATURE (ºC)

OUTPUT CURRENT (A)

02 648

Nat conv

100 LFM

200 LFM

400 LFM

Figure 3 - Safe Operating Area

Vin = 12 V, Output Voltage = 1.8 V (See Note A)

PTV12010

12 Vin single output

NNootteess

A SOA curves represent the conditions at which internal components are

within the Ar

tesyn derating guidelines.

B Characteristic data has been developed from actual products tested at

25 °C. This data is considered typical data for the converter.

PTV12010W Characteristic Data

10uF

Ceramic

(Required)

100uF

Optional

Vin

Rset

0.05W

Track

100uF

(Required)

GND

Inhibit

GND

PTVxx010

416

GNDInhibit

Vo Adj

Vin

Track

Figure 5 - Standard Application

P1-P3 P4-P5

PTV12010WAH

Mfr. #:

Buy PTV12010WAH

Manufacturer:

Texas Instruments

Description:

Non-Isolated DC/DC Converters 1.2-5.5V 8A 12V-In WideAdj SIP Module

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

PTV12010WAH

PTV12010WAH

Products related to this Datasheet