AON6242
Symbol Min Typ Max Units
BV
DSS
60 V
V
DS
=60V, V
GS
=0V 1
T
J
=55°C 5
I
GSS
100 nA
V
GS(th)
Gate Threshold Voltage
1.5 2 2.5 V
I
D(ON)
240 A
3 3.6
T
J
=125°C 4.8 5.8
3.6 4.5 mΩ
g
FS
140 S
V
SD
0.7 1 V
I
S
85 A
C
iss
4240 5305 6370 pF
C
oss
375 540 705 pF
C
rss
6.5 22 38 pF
R
g
0.45 0.9 1.35 Ω
Q
g
(10V) 48 60 72 nC
Q
g
(4.5V) 18 23 28 nC
Q
gs
16 nC
Q
gd
3 nC
t
D(on)
13 ns
V
GS
=0V, V
DS
=0V, f=1MHz
V
GS
=0V, V
DS
=30V, f=1MHz
SWITCHING PARAMETERS
Gate resistance
V
GS
=10V, V
DS
=30V, I
D
=20A
Gate Source Charge
Gate Drain Charge
Total Gate Charge
Electrical Characteristics (T
J
=25°C unless otherwise noted)
STATIC PARAMETERS
Parameter Conditions
I
DSS
Maximum Body-Diode Continuous Current
Input Capacitance
Output Capacitance
Turn-On DelayTime
µA
V
DS
=V
GS,
I
D
=250µA
I
D
=250µA, V
GS
=0V
Zero Gate Voltage Drain Current
V
GS
=10V, V
DS
=5V
V
GS
=10V, I
D
=20A
mΩ
Reverse Transfer Capacitance
V
DS
=0V, V
GS
=±20V
Gate-Body leakage current
Forward Transconductance
Diode Forward Voltage
Static Drain-Source On-Resistance
I
S
=1A,V
GS
=0V
V
DS
=5V, I
D
=20A
V
GS
=4.5V, I
D
=16A
DYNAMIC PARAMETERS
Drain-Source Breakdown Voltage
On state drain current
R
DS(ON)
Total Gate Charge
r
t
D(off)
47 ns
t
f
6.5 ns
t
rr
17 24.5 32 ns
Q
rr
87 125 163
nC
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
I
F
=20A, dI/dt=500A/µs
GS
DS
L
R
GEN
=3Ω
I
F
=20A, dI/dt=500A/µs
Body Diode Reverse Recovery Time
Body Diode Reverse Recovery Charge
Turn-Off Fall Time
Turn-Off DelayTime
A. The value of R
θJA
is measured with the device mounted on 1in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The
Power dissipation P
DSM
is based on R
θJA
and the maximum allowed junction temperature of 150°C. The value in any given application depends
on the user's specific board design, and the maximum temperature of 150°C may be used if the PCB allows it.
B. The power dissipation P
D
is based on T
J(MAX)
=150°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature T
J(MAX)
=150°C. Ratings are based on low frequency and duty cycles to keep
initial T
J
=25°C.
D. The R
θJA
is the sum of the thermal impedance from junction to case R
θJC
and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedance which is measured with the device mounted to a large heatsink, assuming
a maximum junction temperature of T
J(MAX)
=150°C. The SOA curve provides a single pulse rating.
G. The maximum current rating is package limited.
H. These tests are performed with the device mounted on 1 in2 FR-4 board with 2oz. Copper, in a still air environment with TA=25°C.
Rev 0: July 2011 www.aosmd.com Page 2 of 6
