www.tracopower.com
DC/DC Converters
TEN 40N Series 40 Watt
Input Specifications
Input current at no load 12 Vin; 3.3 VDC models: 120 mA typ.
(nominal input voltage) 12 Vin; 5.0, 12 & 24 VDC models: 160 mA typ.
12 Vin; 15 VDC models: 150 mA typ.
12 Vin; 12 & 15 VDC dual output models: 70 mA typ. / 60 mA typ.
24 Vin; 3.3 & 15 VDC models: 75 mA typ.
24 Vin; 5.0, 12 & 24 VDC models: 80 mA typ. / 85 mA typ.
24 Vin; 12 & 15 VDC dual output models: 50 mA typ. / 45 mA typ.
48 Vin; 3.3 VDC models: 40 mA typ.
48 Vin; other single output models: 50 mA typ.
48 Vin; dual output models: 65 mA typ.
Surge voltage (100 ms max.) 12 Vin models: 25 V max.
24 Vin models: 50 V max.
48 Vin models: 100 V max.
Reflected input ripple current 12 Vin models: 50 mA typ.
24 Vin models: 30 mA typ.
48 Vin models: 20 mA typ.
Start-up voltage / under voltage shut down 12 Vin models: 9.0 VDC max. / 8.3 VDC typ.
24 Vin models: 18 VDC max. / 16.5 VDC typ.
48 Vin models: 36 VDC / 33 VDC typ.
Recommended input fuse (slow blow) 12 Vin models: 8000 mA
24 Vin models: 4000 mA
48 Vin models: 2000 mA
Conducted noise (input) EN 55032 class A with external components
see application note
EMC immunity – ESD (electrostatic discharge) EN 61000-4-2, air ±8 kV, contact ±6 kV,
perf. criteria B
– Radiated immunity EN 61000-4-3, 10 V/m, perf. criteria A
– Fast transient / surge (with external input capacitor) EN 61000-4-4, ±2 kV, perf. criteria A
EN 61000-4-5, ±1 kV perf. criteria B
Nippon chemi-con KXG 330 µF, 200 V
– Conducted immunity EN 61000-4-6, 10 Vrms, perf. criteria A
Output Specifications
Voltage set accuracy ±1.0 %
Output voltage adjustment range 24 VDC models: +20 / –10 %
other models: ±10 % with external resistor (see page 3)
Regulation – Input variation Vin min. to Vin max. 0.5 % max.
– Load variation single output models (0 – 100 %): 0.5 % max.
dual output models balanced load (10 – 100 %): 1.0 % max.
Minimum load single output models: 0 %
dual output models: 10 % of rated max current
(operation at lower
load condition will not damage the converters.
However, they may not meet all listed specifications)
Temperature coefficient ±0.02 %/K
Ripple and noise (20 MHz Bandwidth) 3.3 & 5.0 VDC models: 100 mVpk-pk. typ.
with external capacitors 1 µF M/C 10 µF T/C other models: 150 mVpk-pk typ.
Transient response (25 % load step change) 250 µs typ.
Output current limitation 110 % – 150 % of Iout max.
Short circuit protection 24 VDC models: 0.3 Hz. typ.
other models: hiccup mode 1.5 Hz, automatic recovery
Capacitive load 3.3 VDC models: 21’000 µF max.
5.0 VDC models: 13’600 µF max.
12.0 VDC models: 2’400 µF max.
15.0 VDC models: 1’500 µF max.
24.0 VDC models: 600 µF max.
±12.0 VDC models: 1’200 µF max.
±15.0 VDC models: 750 µF max.
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Page 2 of 4