SERIES
MATERIAL NUMBER
CUSTOMER
GENERAL MARKET
41791
SEE CHART
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NUMBER
1 OF *
GENERAL TOLERANCES
(UNLESS SPECIFIED)
MM
INCH
4 PLACES
± ±
3 PLACES
± ±
0.015
2 PLACES
±
0.25
±
0.01
1 PLACES
±
0.38
±
0 PLACES
± ±
ANGULAR TOL
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
DIMENSION UNITS SCALE
MM/IN
2:1
DRWN BY DATE
JSCHAFER
2003/11/07
CHK'D BY
DATE
KSAMIEC
2003/11/07
APPR BY DATE
MARGULIS
2003/11/07
DOCUMENT NUMBER
DOC TYPE
DOC PART
SDA-41791 PSD
000
DRAWING SIZE
THIRD ANGLE PROJECTION
B
KK 156 HEADER ASSEMBLY
FRICTION LOCK VERTICAL SOLID BODY W/O PEGS
PRODUCT CUSTOMER DRAWING
ADD 41791-0090
2016/08/01
2016/08/18
2016/08/25
107107
MKIPPER
JBELL
FSMITH
EC NO:
DRWN:
CHK'D:
APPR:
R
REV
QUALITY
SYMBOLS
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
FORMAT: Eng-lega-master-tb-prod-B
REVISION: C
DATE: 2016/04/04
RELEASE STATUS RELEASE DATE
C
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
A A
B B
C C
D D
E E
15.70
.618
5
-D-
9
CKT. NO. 1
CENTERLINE OF PIN AT TIP
NOT TO VARY FROM
CENTERLINE OF PIN AT DATUM -D-
BY MORE THAN 0.13/.005 IN ANY DIRECTION.
TYP. BETWEEN ANY
2 CONSECUTIVE
CKTS. AT -D-
DETAIL Z
VOIDED CKT.
SEE CHART FOR LOCATION
SEE NOTE 9
55.47
±
0.18
2.184
±
.007
19.66
.774
63.40
±
0.20
2.496
±
.008
59.44
±
0.18
2.340
±
.007
11.73
.462
31.55
1.242
27.58
1.086
23.62
.930
4
2
3
59.28
2.334
51.36
2.022
4 & 5
43.43
1.710
.200
4 & 5
9 & 10
NONE
5 & 6
11 & 12
NONE
NONE
6 & 7
3 & 4
1.70
±
0.05
5 & 6
47.40
1.866
39.47
1.554
5 & 6
9 & 10
4 & 5
8 & 9
35.51
1.398
5 & 6
10 & 11
.067
±
.002
6 & 7
11 & 12
55.32
2.178
6 & 7
12 & 13
MIN
DETAIL Z
SCALE 4:1
5 & 6
63.25
2.490
67.21
2.646
SLOT LOC
BETWEEN CKTS
NONE
4 & 5
5.08
FEATURE MAY BE ON EITHER
SIDE OF THE PART
.394
±
.020
RECOMMENDED P.C.BOARD LAYOUT
3.96REF.
DIM. A REF
.156
±
.002
CENTERLINE OF PIN AT TIP
NOT TO VARY FROM
CENTERLINE OF PIN AT DATUM -D-
BY MORE THAN 0.20/.008 IN ANY DIRECTION.
.446
±
.020
DIM. B
.130
±
.010
SEE NOTE 10
AND DETAIL Z
TIN
±
0.38
±
.015
M
2.41
.075
.201
11.33
±
0.51
3.96
±
0.05
GOLD
TYP
REF
1.91
10.01
±
0.51
.156
DIA TYP
P
5.11
3.30
±
0.25
TYP
NON-ACCUM
.095
TYP
15
DIM. B
19.81
±
0.10
.780
±
.004
43.59
±
0.15
1.716
±
.006
7
39.62
±
0.15
1.560
±
.006
23.77
±
0.10
.936
±
.004
10
35.66
±
0.13
1.404
±
.005
11.89
±
0.08
.468
±
.003
16
7.77
.306
6
47.55
±
0.15
1.872
±
.006
17
71.17
2.802
27.74
±
0.13
1.092
±
.005
8
67.36
±
0.20
2.652
±
.008
13
DIM. A
CKT
3.96
±
0.05
.156
±
.002
51.51
±
0.18
2.028
±
.007
18
15.85
±
0.10
.624
±
.004
11
31.70
±
0.13
1.248
±
.005
12
14
7.92
±
0.08
.312
±
.003
NOTES:
1. MATERIAL: HEADER-GLASS FILLED POLYESTER, 94V-0, MOLDED NATURAL (WHITE).
2. FINISH:
(154-TIN) OVERALL TIN: 0.00254/.000100 MIN.
OVER 0.00127/.000050 MIN NICKEL.
(197-TIN) OVERALL REFLOWED MATTE TIN: 0.00152/.000060 MIN.
OVER 0.00127/.000050 MIN. NICKEL OVERALL.
(222-TIN) OVERALL MATTE TIN: 0.00254/.000100 MIN.
OVER 0.00127/.000050 MIN NICKEL.
(208-15 GOLD) SELECT GOLD: 0.00038/.000015 MIN, SELECT TIN: 0.00254/.000100 MIN,
OVERALL NICKEL UNDERPLATE: 0.00127/.000050 MIN.
(228-30 GOLD) SELECT GOLD: 0.00076/.000030 MIN, SELECT TIN: 0.00254/.000100 MIN,
OVERALL NICKEL UNDERPLATE: 0.00127/.000050 MIN.
(241-20 GOLD) 0.00051/.000020 MIN.
SELECT TIN: 0.00254/.000100 MIN.
OVERALL NICKEL UNDERPLATE: 0.00127/.000050 MIN.
3. PRODUCT SPECIFICATION AND PROCESS PARAMETERS: SEE PS-08-50.
4. PACKAGING INFORMATION: SEE CHARTS.
5. SOLDERABILITY: PER SMES-152.
6. PIN PUSH-OUT FORCE: PRIOR TO SOLDERING, A 3 LB. MINIMUM FORCE (IN EITHER DIRECTION)
7. PARTS ARE STACKABLE END TO END ON 3.96/.156 CENTERS.
8. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002.
9. SLOTS ON BACKWALL ARE BETWEEN CIRCUITS. SEE CHART FOR LOCATION.
10 FEATURE MAY OR MAY NOT EXTEND ACROSS THE ENTIRE FACE OF THE PART "SEE DETAIL Z".
