3
Data Sheet
!
Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifi cations are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifi cations because there is no space for detailed specifi cations. Therefore, please approve our product
specifi cations or transact the approval sheet for product specifi cations before ordering.
http://www.murata.com/
3
Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Film Type
2011.9.8
o
This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design.
Continued from the preceding page.
DLP11TB Series
Frequency (MHz)
10
8
6
4
2
0
1 10 100 1000 10000
Insertion Loss (dB)
DLP11TB800UL2
c
Packaging
c
Rated Value (
p
: packaging code)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance
Operating
Temperature Range
DLP11SN670SL2
p
67ohm ±20% 180mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% -40 to +85°C
DLP11SN121SL2
p
120ohm ±20% 140mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% -40 to +85°C
DLP11SN161SL2
p
160ohm ±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.7ohm±25% -40 to +85°C
DLP11SN900HL2
p
90ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% -40 to +85°C
DLP11SN201HL2
p
200ohm ±20% 110mA 5Vdc 100M ohm 12.5Vdc 3.1ohm±25% -40 to +85°C
DLP11SN241HL2
p
240ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 3.5ohm±25% -40 to +85°C
DLP11SN281HL2
p
280ohm ±20% 90mA 5Vdc 100M ohm 12.5Vdc 4.2ohm±25% -40 to +85°C
DLP11SN331HL2
p
330ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 4.9ohm±25% -40 to +85°C
DLP11SA350HL2
p
35ohm ±20% 170mA 5Vdc 100M ohm 12.5Vdc 0.9ohm±25% -40 to +85°C
DLP11SA670HL2
p
67ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.2ohm±25% -40 to +85°C
DLP11SA900HL2
p
90ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% -40 to +85°C
DLP11RN450UL2
p
45ohm ±25% 100mA 5Vdc 100M ohm 12.5Vdc 0.8ohm±25% -40 to +85°C
DLP11RB150UL2
p
15ohm ±5ohm 100mA 5Vdc 100M ohm 12.5Vdc 0.8ohm±25% -40 to +85°C
DLP11RB400UL2
p
40ohm ±10ohm 100mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% -40 to +85°C
DLP11TB800UL2
p
80ohm ±25% 100mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% -40 to +85°C
Number of Circuit: 1
Differential mode to common mode conversion characteristic (Scd21) at 2.5GHz
DLP11RB/TB: -40dB
Impedance Characteristics between signal lines Z0 (TDR at 50ps)
DLP11RB/TB: 90ohm±15ohm
c
!
Caution/Notice
!
Caution (Rating)
Do not use products beyond the rated current and
rated voltage as this may create excessive heat
and deteriorate the insulation resistance.
Notice
Solderability of Tin plating termination chip might be
deteriorated when low temperature soldering profi le
where peak solder temperature is below the Tin melting
point is used. Please confi rm the solderability of Tin
plating termination chip before use.
c
Differential Mode Transmission Characteristics (Typ.)
Code Packaging Minimum Quantity
L
180mm Embossed Tape
3000 (DLP11S)
4000 (DLP11RN/RB)
5000 (DLP11T)
B
Bulk(Bag) 500
