13
FN8126.3
September 23, 2015
NOTES:
1. V
IL
min. and V
IH
max. are for reference only and are not tested.
2. This parameter is periodically sampled and not 100% tested.
3. SCK frequency measured from V
CC
x 0.1/V
CC
x 0.9
Absolute Maximum Ratings Recommended Operating Conditions
Temperature under bias . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on any pin with
respect to V
SS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +7V
D.C. output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . 300°C
Temperature:
Commercial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage:
-2.7, -2.7A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Blank, -4.5A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.5V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
DC Electrical Specifications (Over the recommended operating conditions unless otherwise specified.)
SYMBOL PARAMETER TEST CONDITIONS/COMMENTS
LIMITS
UNITMIN TYP
(2)
MAX
I
CC1
V
CC
Write Current (Active) SCK = 3.3MHz
(3)
; SO, RESET, RESET = Open 3 mA
I
CC2
V
CC
Read Current (Active) SCK = 3.3MHz
(3)
; SI = V
SS
, RESET, RESET =
Open
2mA
I
SB1
V
CC
Standby Current WDT = OFF CS = V
CC
, SCK, SI = V
SS
,
V
CC
=5.5V 10 µA
I
SB2
V
CC
Standby Current WDT = ON CS = V
CC
, SCK, SI = V
SS
,
V
CC
=5.5V 50 µA
I
LI
Input Leakage Current SCK, SI, WP = V
SS
to V
CC
0.110µA
I
LO
Output Leakage Current SO, RESET, RESET = V
SS
to V
CC
0.1 10 µA
V
IL
(1)
Input LOW Voltage SCK, SI, WP, CS -0.5 V
CC
x 0.3 V
V
IH
(1)
Input HIGH Voltage SCK, SI, WP, CS V
CC
x 0.7 V
CC
+ 0.5 V
V
OL
Output LOW Voltage (SO) I
OL
= 2mA @ V
CC
= 2.7V
I
OL
= 0.5mA @ V
CC
= 1.8V
0.4 V
V
OH1
Output HIGH Voltage (SO) V
CC
> 3.3V, I
OH
= –1.0mA V
CC
- 0.8 V
V
OH2
Output HIGH Voltage (SO) 2V < V
CC
3.3V, I
OH
= –0.4mA V
CC
- 0.4 V
V
OH3
Output HIGH Voltage (SO) V
CC
2V, I
OH
= –0.25mA V
CC
- 0.2 V
V
OLRS
Output LOW Voltage (RESET,
RESET)
I
OL
= 1mA 0.4 V
Capacitance T
A
= +25°C, f = 1MHz, V
CC
= 5V
SYMBOL TEST CONDITIONS MAX UNIT
C
OUT
(2)
Output Capacitance (SO, RESET, RESET) V
OUT
= 0V 8 pF
C
IN
(2)
Input Capacitance (SCK, SI, CS, WP)V
IN
= 0V 6 pF
X5043, X5045