Power-Supply Input for Regulator 1. The voltage range is 2.35V to 3.6V. Connect two 10μF and one 0.1μF
ceramic capacitors from IN1 to PGND1.
Enable Input for Regulator 1. Drive EN1 high to enable regulator 1, or low for shutdown. For always-on
.
Compensation for Regulator 1. COMP1 is the output of the internal voltage-error amplifier. Connect external
compensation network from COMP1 to FB1. See the Compensation Design section. COMP1 is internally
pulled to GND when the output is shut down.
Feedback Input for Regulator 1. Connect FB1 to the center of an external resistor-divider from the output to
. FB1 is high impedance when the IC is shut down.
Soft-Start for Regulator 1. Connect a capacitor from SS1 to GND to set the startup time. See the Setting the
Detailed Description
PWM Controller
The controller logic block is the central processor that
determines the duty cycle of the high-side MOSFET
under different line, load, and temperature conditions.
Under normal operation, where the current-limit and
temperature protection are not triggered, the control
logic block takes the output from the PWM comparator
and generates the driver signals for both high-side and
low-side MOSFETs. It also contains the break-before-
make logic and the timing for charging the bootstrap
capacitors. The error signal from the voltage-error ampli-
fier is compared with the ramp signal generated by the
oscillator at the PWM comparator and, thus, the required
PWM signal is produced. The high-side switch is turned
on at the beginning of the oscillator cycle and turns off
when the ramp voltage exceeds the V
COMP_
signal or
the current-limit threshold is exceeded. The low-side
switch is then turned on for the remainder of the oscilla-
tor cycle. The two switching regulators operate at the
same switching frequency with 180° phase shift to
reduce the input-capacitor ripple current requirement.
Figure 1 shows the MAX8833 functional diagram.
Current Limit
The MAX8833 provides both peak and valley current limits
to achieve robust short-circuit protection. During the
high-side MOSFET’s on-time, if the drain-source current
reaches the peak current-limit threshold (specified in
the
Electrical Characteristics
table), the high-side MOS-
FET turns off and the low-side MOSFET turns on, allow-
ing the current to ramp down. At the next clock, the
high-side MOSFET is turned on only if the inductor cur-
rent is below the valley current limit. Otherwise, the PWM
cycle is skipped to continue ramping down the inductor
current. When the inductor current stays above the valley
current limit for 12μs and the FB_ is below 0.7 x V
REFIN
,
the regulator enters hiccup mode. During hiccup mode,
the SS_ capacitor is discharged to zero and the soft-start
sequence begins after a predetermined time period.
Undervoltage Lockout (UVLO)
When the V
DD
supply voltage drops below the falling
undervoltage threshold (typically 1.9V), the MAX8833
enters its undervoltage lockout mode (UVLO). UVLO
forces the device to a dormant state until the input voltage
is high enough to allow the device to function reliably. In
UVLO, LX_ nodes of both regulators are in the high-
impedance state. PWRGD1 and PWRGD2 are forced low
in UVLO. When V
VDD
rises above the rising undervoltage
threshold (typically 2V), the IC powers up normally as
described in the
Startup and Sequencing
section.
The UVLO circuitry also monitors the IN1 and IN2 sup-
plies. When the IN_ voltage drops below the falling
undervoltage threshold (typically 1.9V), the correspond-
ing regulator shuts down, and corresponding PWRGD_
goes low. The regulator powers up when V
IN_
rises
above the rising undervoltage threshold (typically 2V).
Power-Good Output (PWRGD_)
PWRGD1 and PWRGD2 are open-drain outputs that
indicate when the corresponding output is in regulation.
PWRGD1 is high impedance when V
REFIN
≥ 0.54V and
V
FB1
≥ 0.9 x V
REFIN
. PWRGD1 is low when V
REFIN
<
0.54V, EN1 is low, V
VDD
or V
IN1
is below V
UVLO
, the
thermal-overload protection is activated, or when V
FB1
< 0.9 x V
REFIN
.