Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Radial Lead
NPCAP
TM
-PSFSeries
・
Super low ESR, high ripple current capability
・
ESR 5m
Ω
max. (2 to 4V
dc
)
・
Longer life (20,000 hours at 105
℃
)
・
Rated voltage range : 2 to 16V
dc
・
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・
RoHS2 Compliant
・
Halogen Free
◆
SPECIFICATIONS
Items Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range
2 to 16V
dc
Capacitance Tolerance
±
20%(M) (at 20
℃
, 120Hz)
Surge Voltage
Rated voltage(V)
×
1.15 (at 105
℃
)
Leakage Current
*Note
Shall not exceed values shown in STANDARD RATINGS.
(at 20
℃
after 2 minutes)
Dissipation Factor
(tan
δ
)
0.10 max.
(at 20
℃
, 120Hz)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Z(-25
℃
)/Z(+20
℃
)
≦
1.15
Z(-55
℃
)/Z(+20
℃
)
≦
1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after the rated voltage is applied for 20,000 hours
at 105
℃
.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Bias Humidity Test
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after subjecting them to DC voltage at 60
℃
,
90 to 95% RH for 1,000 hours.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
The initial specified value
ESR 2 to 6.3V
dc
:
≦
The initial specified value
16V
dc
:
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Surge Voltage Test
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105
℃
for 30 seconds
through a protective resistor(R=1k
Ω
) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
The initial specified value
ESR 2 to 6.3V
dc
:
≦
The initial specified value
16V
dc
:
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Failure Rate
0.5% per 1,000 hours maximum (Confidence level 60% at 105
℃
)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆
DIMENSIONS [mm]
Coated Case
L'
15min. 4min.
φD'
φd
Coated Case
L'
15min. 4min.
φD'
φd
F±0.5
F05, F08, H08
FA5, HB5, JB5
F±0.5
(FA5) (HB5, JB5)
F±0.5
Size code
φ
D
φ
d
F
φ
D'
L'
F05
0.45
F08
6.3
0.6
2.5
FA5
0.5
L
+
0.3max.
H08
L
+
1.0max.
HB5
0.6
JB5
10.0
5.0
8.0
3.5
L
+
1.5max.
L
+
1.0max.
(
Note1
)
φD
+
0.5max.
Lower ESR
PSF
PSE P2-42
◆
MARKING
F
6D6
560
2.5
V
Note1 : L+1.2 max. for 6.3V820μF
2-40
CAT. No. E1001R
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
