OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EVAL-ADUCM363QSPZ

P1-P3P4-P6
ADuCM362/ADuCM363 Getting Started Guide
UG-1071
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Te l: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
ADuCM362/ADuCM363 Development Systems Getting Started Tutorial
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 6
FEATURES
ADuCM362/ADuCM363 evaluation board
2 power supply options: 5 V from a USB port connected to
the Segger J-Link OB emulator or 1.8 V to 3.6 V from an
external power supply
On-board resistance temperature detector (RTD) for
temperature measurements
Access to all analog and digital pins
Power and general-purpose LEDs
Reset and download push-buttons
8-pin connector to the Segger J-Link OB emulator
32.768 kHz external crystal
EVALUATION KIT CONTENTS
An evaluation board (EVAL-ADuCM362QSPZ or EVAL-
ADuCM363QSPZ) that facilitates performance evaluation
of the device with minimal external components
An Analog Devices, Inc., Segger J-Link OB emulator (USB-
SWD/UART-EMUZ)
1 USB cable
1 installation DVD
ONLINE RESOURCES
ADuCM362/ADuCM363 data sheet
ADuCM362/ADuCM363 Hardware Reference Manual
GENERAL DESCRIPTION
The ADuCM362/ADuCM363 development system allows
evaluation of ADuCM362 or ADuCM363 silicon. This quick
start guide introduces the support features and tools supplied
with the ADuCM362/ADuCM363 evaluation kit. In addition,
this guide describes how to connect the evaluation hardware.
The getting started guide works as a tutorial, providing instructions
on how to download third party evaluation software tools.
Instructions are also provided on how to load code examples
supplied with the software tools.
The ADuCM362 is a fully integrated, 4 kSPS, 24-bit data
acquisition system that incorporates dual, high performance
multichannel sigma-delta (Σ-Δ) analog-to-digital converters
(ADCs), a 32-bit ARM® Cortex®-M3 processor, and Flash/EE
memory on a single chip.
The ADuCM362 is designed for direct interfacing to external
precision sensors in both wired and battery-powered applications.
The ADuCM363 contains all the features of the ADuCM362
except for the ADC0, which is removed.
This guide gives users the ability to generate and download user
code for use in unique end system requirements.
Complete specifications for the ADuCM362/ADuCM363 are
provided in the ADuCM362/ADuCM363 data sheet and should
be consulted in conjunction with this user guide when using the
evaluation board.
EVAL-ADuCM362QSPZ/EVAL-ADuCM363QSPZ EVALUATION BOARD
15169-001
Figure 1.
UG-1071 ADuCM362/ADuCM363 Getting Started Guide
Rev. 0 | Page 2 of 6
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Kit Contents ................................................................... 1
Online Resources .............................................................................. 1
General Description ......................................................................... 1
EVA L-ADuCM362QSPZ/EVA L-ADuCM363QSPZ evaluation
board ................................................................................................... 1
Revision History ............................................................................... 2
Getting Started .................................................................................. 3
Software Installation Procedures ................................................ 3
Keil µVision5 ..................................................................................3
IAR Embedded Workbench .........................................................4
Elves.exe ..........................................................................................4
Evaluation Board Setup Procedures ...........................................4
Windows Serial Downloader ...........................................................5
Preparing for Download ...............................................................5
Downloading Using CM3WSD ...................................................5
Running the Downloaded File ....................................................5
REVISION HISTORY
10/2016—Revision 0: Initial Version
ADuCM362/ADuCM363 Getting Started Guide UG-1071
Rev. 0 | Page 3 of 6
GETTING STARTED
SOFTWARE INSTALLATION PROCEDURES
Perform the steps described in this section before plugging any
USB devices into the PC.
1. Close all open applications.
2. Insert the installation DVD into the DVD drive.
3. Double-click ADuCM36x.exe and follow the on-screen
instructions. A menu displays installation options as shown
in Figure 2.
15169-002
Figure 2. Installation Options
The following components install by default:
• Example code and function sets for most peripherals.
• An Elves.exe application to easily choose functions from
the provided function sets followed by choosing from the
function parameters.
The following components are optional installations:
• Keil development tools (a compiler, debugger, and
programming tools). The Keil μVision 5 software version
is used.
• IAR Embedded Workbench development tools (a compiler,
debugger, and programming tools).
• Segger J-Link drivers for the J-Link emulator.
The J-Link software is selected by default in the installation menu,
shown in Figure 2. It is advised to leave it selected. The J-Link
software automatically installs the J-Link serial port driver. Select
Install USB Driver for J-Link-OB with CDC, shown in Figure 3.
If that step is missed, run JLinkCDCInstaller_V1.2b.exe
located in the ADuCM36x\Segger folder.
13967-003
Figure 3. Installing Link Software
If using the IAR tools, the entire contents of the supplied arm
directory (for example, C:\ADuCM36x…\IAR\IAR_M36x_
Patch.zip\arm) must be copied to the IAR tools directory (for
example, C:\Program Files\IAR Systems\ Embedded
Workbench 7.3 Kickstart\arm).
Future updates are available from the Analog Devices
FTP website.
KEIL µVISION5
The Keil µVision5 integrated development environment (IDE)
integrates all the tools necessary to edit, assemble, and debug
code. The fastest way to start is to open an existing Keil µVision5
project by following these steps:
1. In Keil µVision5, select Project > Open Project.
2. Browse to the folder where the ADuCM362/ADuCM363
software is installed (such as, C:\ADuCM36x...).
3. Open the file DIO.uvproj in the folder
code\ADuCM362\examples\DIO. This file launches an
example project.
4. Compile and download to the ADuCM362/ADuCM363 on
the evaluation board.
5. To run the example code, press RESET on the evaluation
board or enter debug mode by clicking the Start/Stop
Debug Session (Ctrl+F5) button (see Figure 4) and then
click Run (F5) (see Figure 5).
15169-009
Figure 4. Download and Debug Button
15169-010
Figure 5. Run (F5) Button
6. When running, the red LED marked DISPLAY on the
evaluation board flashes.
P1-P3P4-P6

EVAL-ADUCM363QSPZ

Mfr. #:
Buy EVAL-ADUCM363QSPZ
Manufacturer:
Analog Devices Inc.
Description:
ADUCM363 Microcontroller Development Board 0.032768MHz CPU Flash Win
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet