Exar Corporation 48720 Kato Road, Fremont CA, 94538 (510) 668-7000 FAX (510) 668-7017 www.exar.com
XRA1200/1200P
8-BIT I2C/SMBUS GPIO EXPANDER
SEPTEMBER 2011 REV. 1.0.0
GENERAL DESCRIPTION
The XRA1200/1200P is an 8-bit GPIO expander with
an I
2
C/SMBus interface. After power-up, the
XRA1200 has internal 100K ohm pull-up resistors on
each I/O pin that can be individually enabled. The
XRA1200P have the internal pull-up resistors
enabled upon power-up in case it is necessary for the
inputs to be in a known state.
In addition, the GPIOs on the XRA1200/1200P can
individually be controlled and configured. As outputs,
the GPIOs can be outputs that are high, low or in
three-state mode. The three-state mode feature is
useful for applications where the power is removed
from the remote devices, but they may still be
connected to the GPIO expander.
As inputs, the internal pull-up resistors can be
enabled or disabled and the input polarity can be
inverted. The interrupt can be programmed for
different behaviors. The interrupts can be
programmed to generate an interrupt on the rising
edge, falling edge or on both edges. The interrupt
can be cleared if the input changes back to its original
state or by reading the current state of the inputs.
The XRA1200/1200P are enhanced versions of other
8-bit GPIO expanders with an I
2
C/SMBus interface.
The XRA1200 is pin and software compatible with the
CAT9534 and PCA9534. The XRA1200P is pin and
software compatible with the CAT9554 and
PCA9554. The XRA1200/1200P are also pin
compatible with the PCA9554A and TCA9554A.
The XRA1200/1200P are available in 16-pin QFN
and 16-pin TSSOP packages.
FEATURES
1.65V to 3.6V operating voltage
8 General Purpose I/Os (GPIOs)
5V tolerant inputs
Maximum stand-by current of 1uA at +1.8V
I
2
C/SMBus bus interface
I
2
C clock frequency up to 400kHz
Noise filter on SDA and SCL inputs
Up to 32 I
2
C Slave Addresses
Individually programmable inputs
Internal pull-up resistors
Polarity inversion
Individual interrupt enable
Rising edge and/or Falling edge interrupt
Input filter
Individually programmable outputs
Output Level Control
Output Three-State Control
Open-drain active low interrupt output
Pin and software compatible with CAT9534,
CAT9554, PCA9534, and PCA9554
3kV HBM ESD protection per JESD22-A114F
200mA latch-up performance per JESD78B
APPLICATIONS
Personal Digital Assistants (PDA)
Cellular Phones/Data Devices
Battery-Operated Devices
Global Positioning System (GPS)
Bluetooth
XRA1200/1200P
2
8-BIT I2C/SMBUS GPIO EXPANDER REV. 1.0.0
FIGURE 1. XRA1200 BLOCK DIAGRAM
I
2
C/
SMBus
Interface
A2
A1
SCL
SDA
GPIO
Control
Registers
A0
IRQ#
P0
GPIOs
P1
P2
P3
P4
P5
P6
P7
VCC (1.65V – 3.6V)
GND
ORDERING INFORMATION
PART NUMBER PACKAGE
NUMBER OF
GPIO
S
OPERATING TEMPERATURE
R
ANGE
DEVICE STATUS
XRA1200IL16-F QFN-16 8 -40°C to +85°C Active
XRA1200IL16TR-F QFN-16 8 -40°C to +85°C Active
XRA1200PIL16-F QFN-16 8 -40°C to +85°C Active
XRA1200PIL16TR-F QFN-16 8 -40°C to +85°C Active
XRA1200IG16-F TSSOP-16 8 -40°C to +85°C Active
XRA1200IG16TR-F TSSOP-16 8 -40°C to +85°C Active
XRA1200PIG16-F TSSOP-16 8 -40°C to +85°C Active
XRA1200PIG16TR-F TSSOP-16 8 -40°C to +85°C Active
NOTE: TR = Tape and Reel, F = Green / RoHS
FIGURE 2. PIN OUT ASSIGNMENTS
XRA1200/
XRA1200P
16-Pin QFN
P1
P2
P0
A2
GND
P3
P4
P5
A0
A1
VCC
SDA
P7
P6
IRQ#
SCL
XRA1200/
XRA1200P
16-Pin TSSOP
3
5
4
7
6
8
1
2
A0
A1
A2
P0
P1
P2
P3
GND
9
10
11
12
13
14
15
16 VCC
SDA
SCL
IRQ#
P7
P6
P5
P4
16 15 14 13
5678
2
1
3
4
11
12
10
9
XRA1200/1200P
3
REV. 1.0.0 8-BIT I2C/SMBUS GPIO EXPANDER
PIN DESCRIPTIONS
Pin Description
NAME
PIN# PIN#
TYPE DESCRIPTION
I2C INTERFACE
SDA 13 15 I/O
I
2
C-bus data input/output (open-drain).
SCL 12 14 I
I
2
C-bus serial input clock.
IRQ# 11 13 OD
Interrupt output (open-drain, active LOW).
A0
A1
A2
15
16
1
1
2
3
I
I
I
These pins select the I
2
C slave address. See Table 1.
GPIOs
P0
P1
P2
P3
P4
P5
P6
P7
2
3
4
5
7
8
9
10
4
5
6
7
9
10
11
12
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
General purpose I/Os P0-P7. All GPIOs are configured as inputs upon power-
up or after a reset. After power-up or reset, the internal pull-up resistors are
enabled for the XRA1200P. The internal pull-up resistors are disabled for the
XRA1200.
ANCILLARY SIGNALS
VCC 14 16 Pwr
1.65V to 3.6V VCC supply voltage.
GND 6 8 Pwr
Power supply common, ground.
GND Center
Pad
- Pwr
The exposed pad at the bottom surface of the package is designed for thermal
performance. Use of a center pad on the PCB is strongly recommended for ther
-
mal conductivity as well as to provide mechanical stability of the package on the
PCB. The center pad is recommended to be solder masked defined with open
-
ing size less than or equal to the exposed thermal pad on the package bottom to
prevent solder bridging to the outer leads of the device. Thermal vias must be
connected to GND plane as the thermal pad of package is at GND potential.
Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain.
QFN-16 TSSOP-16

XRA1200PIL16-F

Mfr. #:
Manufacturer:
MaxLinear
Description:
Interface - I/O Expanders 8 Bit I2C SMBus GPIO Expander
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union