File Name:HLG-320H-SPEC 2018-05-29
320W Constant Voltage + Constant Current LED Driver
HLG-320H series
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
CURRENT ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
Note.6
HOLD UP TIME (Typ.)
VOLTAGE RANGE
Note.5
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.) (230Vac)
EFFICIENCY (Typ.) (277Vac)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WORKING TEMP.
MAX. CASE TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
PACKING
OVER CURRENT
Note.4
OVER VOLTAGE
OVER TEMPERATURE
Adjustable for A/AB/C-Type only (via built-in potentiometer)
Adjustable for A/C-Type only (via built-in potentiometer)
2500ms,80ms/115VAC 500ms,80ms/230VAC
15ms / 115VAC, 230VAC
47 ~ 63Hz
3.5A / 115VAC 1.65A / 230VAC 1.45A / 277VAC
<0.75mA / 277VAC
95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
Compliance to EN55015, EN55032 (CISPR32) Class B, EN61000-3-2 Class C ( ) ; EN61000-3-3,EN61000-3-3@ load 50%≧ ,
GB17743 and GB17625.1,EAC TP TC 020
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (),surge immunity Line-Earth 4KV, Line-Line 2KV
Tcase= -40 ~ +90℃
(Please refer to "OUTPUT LOAD vs TEMPERATURE" section)
Tcase= +90℃
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH
℃
±℃ ℃
0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
IP65 or IP67 (except for HLG-320H C-type); J61347-1, J61347-2-13 (except for HLG-320H C-type) EAC TP TC 004 approved,
UL8750(type”HL”), CSA C22.2 No. 250.0-08; EN/AS/NZS 61347-1, EN/AS/NZS 61347-2-13, EN62384 independent; GB19510.1,GB19510.14;
157.1K hrs min. MIL-HDBK-217F (25 )℃
252*90*43.8mm (L*W*H)
1.88Kg
; 8pcs/16Kg/0.92CUFT
Shut down and latch off o/p voltage, re-power on to recover
Shut down and latch off o/p voltage, re-power on to recover
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE
Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
SHORT CIRCUIT
Hiccup mode, recovers automatically after fault condition is removed
14 ~ 17V 17.5 ~ 21V
22.5 ~ 27V
27 ~ 33V
33 ~ 37V
40 ~ 46V 53.5 ~ 60V
46.5 ~ 53V 59 ~ 65V
91%
91.5%
92.5%
93%
93.5%
94%
94%
94.5%
94%
94.5%
94.5%
95%
95%
95%
95%
95%
95%
95%
±3.0%
11 ~ 22A
±2.0%
9.5 ~ 19A
±1.5%
7.5 ~ 15A
±1.0%
6.67 ~ 13.34A
±1.0%
5.35 ~ 10.7A
±1.0%
4.45 ~ 8.9A
±1.0%
3.35 ~ 6.7A
±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
±0.5%
±0.5%
±2.0%
±1.5% ±1.0% ±0.5% ±0.5%
±0.5%
±0.5%
±1.0%
2.97 ~ 5.95A
±0.5%
±0.5%
±1.0%
3.8 ~ 7.65A
±0.5%
±0.5%
HLG-320H-12
HLG-320H-15
HLG-320H-20
HLG-320H-24
HLG-320H-30
HLG-320H-36
HLG-320H-48
12V
6 ~12V
15V
7.5 ~ 15V
20V
10 ~ 20V
24V
12 ~ 24V
30V
15 ~ 30V
36V
18 ~ 36V
48V
24 ~ 48V
22A 19A 15A 13.34A
10.7A
8.9A
6.7A
264W 285W 300W 320.16W 321W
320.4W
321.6W
150mVp-p 150mVp-p
13.5 ~ 17V
150mVp-p
17 ~ 22V
150mVp-p
21 ~ 26V
200mVp-p
26 ~ 32V
250mVp-p
32 ~ 39V
250mVp-p
43 ~ 52V10.8 ~ 13.5V
HLG-320H-54
54V
27 ~ 54V
5.95A
321.3W
350mVp-p
49 ~ 58V
HLG-320H-42
42V
21 ~ 42V
7.65A
321.3W
250mVp-p
38 ~ 45V
EMC IMMUNITY
EMC EMISSION
COLD START 70A(t =1010 s measured at 50% I ) at 230VAC;
width peak Per NEMA 410
μ
TOTAL HARMONIC DISTORTION
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
1 unit (circuit breaker of type B) / 2 units (circuit breaker of type C) at 230VAC
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
℃
CONSTANT CURRENT REGION
Note.4
NOTE
90 ~ 305VAC 127 ~ 431VDC
(Please refer to "STATIC CHARACTERISTIC" section)
PF 0.98/115VAC, PF 0.95/230VAC, PF 0.94/277VAC @ full load≧≧≧
(Please refer to " " section)POWER FACTOR (PF) CHARACTERISTIC
THD< 20% (@ load 50% / 115VAC,230VAC; @ load 75% / 277VAC)≧≧
(Please refer to TOTAL HARMONIC DISTORTION (THD) section)""
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Please refer to "DRIVING METHODS OF LED MODULE".
5. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
7. driver
The is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED can only be used behind a switch without permanently
driver
connected to the mains.
9. This series meets the typical life expectancy of >62,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75 or less.℃
1 . Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com.0
11. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
EAC TP TC 020
