MPZ2012S300ATD25 Datasheet MPZ2012S300ATD25, FH48-20S-0.5SV | P7-P8

FH48 Series●0.5 mm Pitch, 6.18 mm Height, Vertical Mount, Shielded FFC High Speed Connectors

Connector handling and precautions

Handling and precautions

Care must be taken to the handling of this connector. Check the followings before using the product. The ﬁ gures and values

described in the precautions may differ from the standard values of the product.

[Precautions for board implementation]

◆ Board warp

Avoid board warp if possible.

The flatness of the connector is 0.1mm or smaller, and a large warp could cause solder failure.

◆ Load on connector

When the emboss is extracted from the reel or when the connector is vacuum picked up from the emboss, avoid an

excessive force (over 1 N) to the un-mounted connector. Otherwise the connector could be damaged.

Also, do not insert FFC or handle the connector before inserting the connector.

[Precautions for board handling after implementation]

◆ Load on board

-When a board is divided to make multiple boards

-When a board is fixed with screws.

In the assembling process such as the above, no load should be applied to

the board. Otherwise the connector could be damaged.

◆ Board warp

When the board width is 100mm, the board warp should be 1mm or smaller

for the use. (Right figure)

The board warp could cause a load on the connector and damage it.

[Precautions for FFC insertion and mating]

◆ Opening and closing of actuator

The connector, when delivered, is ready for FFC insertion. When FFC is inserted and the actuator is rotated by 90°,

the connector is in a FFC mating locked state. Do not rotate the actuator before inserting FFC.

◆ Contact direction

Insert the connector with the FFC’s exposed conductor side on the housing and with the FFC stiffening plate on the

actuator.

◆ FFC insertion

Securely insert FFC vertically to the connector.

6XijVidg

=djh^c\

.%

8dccZXidg^cYZa^kZgnhiViZ

;;8XVcWZ^chZgiZY#

;;8bVi^c\adX`ZY

6XijVidg

;;8^chZgi^dchiVgih

:medhZY[VXZd[;;8XdcYjXidg

;;8hi^[[Zc^c\eaViZ

8dccZXidg

7dVgY

&B6M

&%%

&B6M

&%%

FH48 Series●0.5 mm Pitch, 6.18 mm Height, Vertical Mount, Shielded FFC High Speed Connectors

Handling and precautions

◆ Actuator handling

(1) The actuator can rotate about the rotation axis. Handle it as it rotates.

(2) The actuator does not rotate by more than 90°. Do not apply an excessive force to rotate it more. Otherwise the

terminal is deformed or the actuator is damaged.

(3) Do not pull or hook the actuator. Otherwise damage could be caused. (Only the rotation motion described above is

allowed.)

◆ Check of lock

(1) When locking the actuator, make sure that it is parallel to the board face.

(2) After mating and locking FFC, make sure that the FFC positioning tab does not come on the FFC positioning

guide. If the FFC positioning tab runs over the FFC positioning guide, contact failure could be caused.

[Precautions for FFC handling after mating FFC]

◆ Load on FFC

When handling FFC, do not apply a load directly to it.

If FFC is bent near the connector when it is used, contact

failure ordisconnection or damage of FFC could be

caused.

In particular, do not bend FFC sharply at the insertion

point to the actuator direction.

[Precautions for pulling FFC]

◆ FFC needs to be pulled out with the actuator locked.

To circumvent the FFC positioning guide, pull it out at an angle

of about 7° from the perpendicular direction to the board.

[Other precautions]

◆ Precautions for manual soldering

For manual soldering for repair or other purposes, see the followings.

(1) Do not make reflow or manual soldering with FFC inserted in the connector.

(2) Do not apply excessive heat. Prevent a soldering iron from contacting a part other than the lead wire of the

connector. Otherwise the connector may deform or melt.

(3) Do not supply an excessive amount of solder (flux).

If too much solder (flux) is applied on the terminal, a part of the solder or flux would adhere to the contact or

actuator’s rotation axis and cause contact failure or rotation failure of the actuator.

.%

GdiVi^dcVm^h

;;8edh^i^dc^c\\j^YZ

;;8edh^i^dc^c\iVW

Load: 0.05x n N MAX

(n: No. of pos.)

;;8edh^i^dc^c\\j^YZ

,

;;8edh^i^dc^c\iVW

The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.

The contents of this catalog are current as of date of 11/2013. Contents are subject to change without notice for the purpose of improvements.

6-3,Nakagawa Chuoh-2-Chome,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN

TEL:

81-45-620-3526 Fax:

81-45-591-3726

http://www.hirose.com

http://www.hirose-connectors.com

P1-P3 P4-P6 P7-P8

MPZ2012S300ATD25

Mfr. #:

Buy MPZ2012S300ATD25

Manufacturer:

TDK

Description:

Ferrite Beads 0805 30ohms 6000mA Power Line AEC-Q200

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

MPZ2012S300ATD25

MPZ2012S300ATD25

Products related to this Datasheet