1062258-1 Datasheet 1062258-1 | P1-P2

Housing Subassembly Center Contact Ferrule Heat-Shrink Tubing

CONNECTOR

CABLE TYPE

TE CONNECTIVITY PART NO. PREVIOUS PART NO.

1062258-1 1031 5002 95

RG174/U, 179, 187, 188, 316

1081231-1 1031 5002 00

1045481-1 1031 5002 00

1045482-1 1031 5002 02

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1 of 2

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111



PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

LOC B

408-4790



SSMA Straight Cable Plug Connectors

22 AUG 11 Rev B

Figure 1

1. INTRODUCTION

These instructions cover the assembly of the SSMA

Straight Cable Plugs listed in Figure 1. Figure 1 also

lists the cable types required for the various

connectors.

All of these connectors ar

e solder-type connectors.

Tooling required for the application is listed in Figure 2.

TE PART NO.

PART NO.

DESCRIPTION

1055463-1

2098 5237 10

-4579)

Center Contact Holder

1055461-1

2098 5236 02

-1888)

Locator Tool

Figure 2

NOTE

Dimensions in this document are in metric units

[with U.S. customary units in brackets], unless

otherwise specified.



Reasons for reissue of this document can be found in

Section 3, REVISION SUMMARY.

2. ASSEMBLY

2.1. Preparing the Coaxial Cable End (Fig

ure 3)

1. Place the heat-shrink tubing and ferrule on

the cable.

2. Remove the end portion of the cable jacket to

xpose the cable braid.

3. Trim the braid to the length shown in Figure 3.

4. Trim the cable dielectric to length.

5. Trim the inner conductor to length.

6. Flare the cable braid.

2.2. Soldering Center Contact to Inner Conductor 

(Figure 4)

1. Tin the inner conductor

2. Place center contact in center contact holder (see

Fig

ure 4)

3. Heat the center contact with a sold

ering iron and

carefully push it over the inner conductor to rest

firmly against the dielectric.

Ferrule

Inner

Conductor

Dielectric

Heat-Shrink Tubing

Cable

Jacket

9.14

[.360]

5.1

[.200]

2.3

[.090]

Figure 3

Center Contact

Holder T-4579

Center Contact Pin

Heat Here

Cable Dielectric

408-4790

2 of 2

Rev B

Figure 4

DANGER

STOP

To avoid personal injury, be sure to follow all local

safety practices when using soldering equipment.



4. Remove the excess solder or splatter.

2.3. Soldering Cable Braid to the Housing 

Subassembly (Figure 5)

1. Secure the locator tool to the threads of the

housing subassembly.

2. Position and secure the housing subassembly in

a small bench vice.

3. Insert cable into the housing subassembly and

seat it

firmly.

4. Slide the ferrule over the flared cable braid.

5. Hold the cable firmly seated and solder through

the

holes in the ferrule.

DANGER

STOP

To avoid personal injury, be sure to follow all local

safety practices when using soldering equipment.



6. Trim and remove excess cable braid strands.

Locator Tool

T-1888

Cable

Braid

Housing

Subassembly

Ferrule

Solder Through the

Holes in the Ferrule

Figure 5

2.4. Shrink Heat-Shrink Tubing to the Cable (Figure 6)

1. Position the heat-shrink tubing over the ferrule as

shown in Figure 6.

2. Apply indirect heat with a “thermo gun” to shrink

the h

eat-shrink tubing.

3. Remove the locator tool.

Locator Tool

T-1888

Housing

Subassembly

Heat-Shrink Tubing

Figure 6

2.5. Inspecting the Completed Assembly

Adherence to the assembly steps should yield the

dimensions shown in Figure 7.

Center

Contact

Dielectric

Edge

Reference

Plane

0.00 - 0.25 [.000 - .010]

Contact and Dielectric

Figure 7

3. REVISION SUMMARY

Updated format to current corporate requirements

P1-P2

1062258-1

Mfr. #:

Buy 1062258-1

Manufacturer:

TE Connectivity

Description:

RF Connectors / Coaxial Connectors SCD 1031 5002 95 SSMA

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

1062258-1