4
FN6037.4
August 31, 2015
Absolute Maximum Ratings Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V- to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15 to 0.3V
All Other Pins (Note 3) . . . . . . . . . . . . . ((V-) - 0.3V) to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, IN, NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . 100mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . .>2kV
Operating Conditions
Temperature Range
ISL4314XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Thermal Resistance (Typical)
JA
(°C/W)
16 Ld TSSOP Package (Note 4) . . . . . . . . . . . . . . . 150
16 Ld QFN Package (Note 5). . . . . . . . . . . . . . . . . . 75
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Moisture Sensitivity (See Technical Brief TB363)
All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(TSSOP - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Signals on NC, NO, COM, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum current ratings.
4.
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
5.
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379 and Tech Brief TB389.
Electrical Specifications: 5V Supply Test Conditions: V
SUPPLY
= 4.5V to 5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(°C)
(NOTE 6)
MIN TYP
(NOTE 6)
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full V- - V+ V
ON Resistance, R
ON
V
S
= 4.5V, I
COM
= 10mA, V
NO
or V
NC
= 3.5V,
See Figure 5
25 - 18 25
Full - - 30
R
ON
Matching Between Channels,
R
ON
V
S
= 4.5V, I
COM
= 10mA, V
NO
or V
NC
= 3V 25 - 0.5 2
Full - - 4
R
ON
Flatness, R
FLAT(ON)
V
S
= 4.5V, I
COM
= 10mA, V
NO
or V
NC
= 0V, 3V,
Note 8
25 - - 5
Full - - 5
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V
S
= 5.5V, V
COM
= 4.5V, V
NO
or V
NC
= +4.5V,
Note 7
25 -0.1 - 0.1 nA
Full -2.5 - 2.5 nA
COM OFF Leakage Current,
I
COM(OFF)
V
S
= 5.5V, V
COM
= 4.5V, V
NO
or V
NC
= +4.5V,
Note 7
25 -0.1 - 0.1 nA
Full -2.5 - 2.5 nA
COM ON Leakage Current,
I
COM(ON)
V
S
= 5.5V, V
COM
= V
NO
or V
NC
= 4.5V, Note 7 25 -0.2 - 0.2 nA
Full -5 - 5 nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V
INH
Full 2.4 1.6 - V
Input Voltage Low, V
INL
Full - 1.5 0.8 V
Input Current, I
INH
, I
INL
V
S
= 5.5V, V
IN
= 0V or V+ Full -1 - 1 A
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V
S
= 4.5V, V
NO
or V
NC
= 3V, R
L
= 300, C
L
= 35pF,
V
IN
= 0 to 3V, See Figure 1
25 - 52 65 ns
Full - - 75 ns
Turn-OFF Time, t
OFF
V
S
= 4.5V, V
NO
or V
NC
= 3V, R
L
= 300, C
L
= 35pF,
V
IN
= 0 to 3V, See Figure 1
25 - 40 50 ns
Full - - 55 ns
Break-Before-Make Time Delay
(ISL43145 only), t
D
V
S
= 5.5V, V
NO
or V
NC
= 3V, R
L
= 300, C
L
= 35pF,
V
IN
= 0 to 3V, See Figure 3
Full 5 19 - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0, See Figure 2 25 - - 5 pC
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 7 25 - 10 - pF
ISL43143, ISL43144, ISL43145
