LH1523BB, LH1523BAC, LH1523BACTR
www.vishay.com
Vishay Semiconductors
Rev. 1.6, 07-Jul-11
2
Document Number: 83822
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1)
Breakdown occurs between the output pins external to the package.
(2)
Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through
hole devices (DIP).
Note
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
ABSOLUTE MAXIMUM RATINGS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
INPUT
LED continuous forward current I
F
50 mA
LED reverse voltage I
R
10 μA V
R
5V
OUTPUT
DC or peak AC load voltage I
L
50 μA V
L
200 V
Continuous DC load current,
one pole operating
I
L
200 mA
Continuous DC load current,
two poles operating
I
L
140 mA
Peak load current (single shot) t = 100 ms I
P
400 mA
SSR
Ambient temperature range T
amb
- 40 to + 85 °C
Storage temperature range T
stg
- 40 to + 125 °C
Pin soldering temperature
(2)
t = 10 s max. T
sld
260 °C
Input to output isolation voltage t = 1 s, I
ISO
= 10 μA max. V
ISO
3750 V
RMS
Pole-to-pole isolation voltage (S1 to S2)
(1)
,
(dry air, dust free, at sea level)
1600 V
Output power dissipation (continuous) P
diss
600 mW
ELECTRICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
INPUT
LED forward current, switch turn-on I
L
= ± 200 mA, t = 10 ms I
Fon
0.2 0.9 mA
LED forward current, switch turn-off V
L
= ± 150 V I
Foff
12mA
LED forward voltage I
F
= 10 mA V
F
1.15 1.22 1.45 V
OUTPUT
On-resistance I
F
= 0 mA, I
L
= 50 mA R
ON
10 15
Off-resistance I
F
= 5 mA, V
L
= ± 100 V R
Off
0.1 1.4 G
Off-state leakage current I
F
= 5 mA, V
L
= ± 200 V I
O
0.07 1 μA
Output capacitance I
F
= 5 mA, V
L
= 50 V C
O
50 pF
TRANSFER
Capacitance (input to output) V
ISO
= 1 V C
IO
3pF
SWITCHING CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Turn-on time I
F
= 10 mA, I
L
= 50 mA t
on
13ms
Turn-off time I
F
= 10 mA, I
L
= 50 mA t
off
23ms
