DO NOT
SCALE FROM
THIS PRINT
XFWS-XX-XX-XX-S-XX-X
-01 THRU -20
ROW SPECIFICATION
-S: SINGLE
(HFWS: USE HFSW-20-200)
(FWS: USE FSW-20-200)
LEAD STYLE
(SEE TABLE 1, 2, 3)
PLATING SPECIFICATION
-T: TIN (USE T-1S8-XX-T)
-TM: MATTE TIN (USE T-1S8-XX-TM)
OPTION
-RA: RIGHT ANGLE (POST)
(N/A) WITH -VS OPTION)
(SEE FIG 3 SHEET 2)
-VS: VERTICAL SURFACE MOUNT
(HFWS ONLY, 2 POS MIN.)
(SEE FIG 2 SHEET 2)
LEAVE BLANK FOR THRU HOLE
(SEE FIG 1 SHEET 1)
OPTION
-P: PICK AND PLACE PAD
(USE PPP-47, SEE FIG 2)
(-VS ONLY, 3 POS MIN.
.275 MIN POST HEIGHT)
(SEE FIG 4 SHEET 2)
-H: HIGH TEMP (USE HFSW-20-200)
BLANK: STANDARD (USE FSW-20-200)
BODY SPECIFICATION
No OF POSITIONS
.100
REF
2.54
.045
SQ REF
1.14
"B"
(SEE NOTE 4)
2
MAX SWAY
(EITHER DIRECTION)
C
T-1S8-XX-TX
(No OF POSITIONS x .200 [5.08])
.015 [.38]
(No OF POSITIONS x .200[5.08])
- .200[5.08]
.100 2.54
REF
.250 6.35
REF
.125
REF
3.18
01
(H)FSW-20-200
"C" REF
(-05 LEAD STYLE:
SEE NOTE 11)
"A" REF
2
MAX TOE
(EITHER DIRECTION)
C
(XFWS-08-XX-T-S SHOWN)
SEE NOTE 9
THRU HOLE OPTION
FIG 1
C
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3]
2
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
.045 [1.14] SQ POST POWER BLOCK ASSEMBLY, .200 [5.08]
BY:
XFWS-XX-XX-XX-S-XX-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
T. WERNE
9/27/2000
2
1
SHEET SCALE: 1.5:1
INSULATOR:
HFSW: VECTRA E130i, COLOR: NATURAL
FWS: VALOX 420 SEO, COLR: BLACK
TERMINAL: PHOS BRONZE
F:\DWG\MISC\MKTG\XFWS-XX-XX-XX-S-XX-X-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: 3 lbs.
3. MAXIMUM ALLOWABLE BOW: .003[.08] IN/IN AFTER ASSEMBLY.
4. HEIGHT VARIATION BETWEEN ANY 2 PINS: .005[.13] MAX.
5. - - - - -
6. - - - - -
7. MAXIMUM ALLOWABLE FLASH: .020[.51].
8. MAXIMUM PIN ROTATION IN BODY: 2 DEGREES.
9. THRU HOLE AND RIGHT ANGLE PARTS TO BE BULK PACKAGED.
10. -VS PARTS TO BE PACKAGED AS;
POSITIONS -02 AND -03: LAYER PACKAGED,
POSITIONS -04 THRU -20: TUBE PACKAGED.
11. TAILS ARE TO BE SHEARED TO PROPER LENGTH.
12. T-1S8-XX MUST BE FLIPPED IN THE OPPOSITE WAY AS THE
SELECTIVE PINS TO REDUCE THE NUMBER OF BAND MARKS
IN THE POST AREA.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION Q
