DG2707DN-T1-E4

Vishay Siliconix
DG2707
Document Number: 68397
S11-0176-Rev. B, 07-Feb-11
www.vishay.com
1
High Speed, Low Voltage, 3 , Differential 4:1 CMOS Analog
Multiplexer/Switch
DESCRIPTION
The DG2707 is a high speed, low voltage, 3 , differential
4:1 multiplexer. It operates from a 1.65 V to 4.3 V single
power supply. All channels guaranteed break before make
switching. When powered with single 3.15 V supply, channel
to channel ON Resistance matching is within 0.3 .
All control logic input has 0.5 V to 1.65 V threshold. The EN
pin enables cascading of the multiplexers. It features a
120 MHz - 3 dB bandwidth, - 90 dB crosstalk and - 70 dB
off-isolation at 1 MHz.
The DG2707 comes in a small miniQFN-16 lead package
(1.8 mm x 2.6 mm x 0.75 mm). As a committed partner to
community and the environment, Vishay Siliconix
manufactures this product with the lead (Pb)-free device
terminations and is 100 % RoHS complicant.
FEATURES
Low voltage operation (1.65 V to 4.3 V)
Low on-resistance - R
ON
: 2.8 typ. at 3.15 V
Low voltage logic threshold
Low crosstalk: - 70 dB
High off-isolation: - 90 dB
Ultra small package: miniQFN16 of 1.8 mm x 2.6 mm
APPLICATIONS
A/V and analog signal routing
Battery operated devices
Data acquisition systems
Communications systems
Medical and ATE equipments
FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION
ORDERING INFORMATION
Temp. Range Package Part Number
- 40 °C to 85 °C miniQFN-16 DG2707DN-T1-E4
1
234
13
15
16
14
12
11 10 9
8
6
5
7
DECODER
UXX
Pin 1: LONG LEAD
EN
S6
D2
S7
S3
D1
S2
N/C
Top View
miniQFN-16L
Device Marking: UXX
Traceability Code:
U is DG2707DN
XX = Date/Lot
S8
V+IN1S1
S5
GNDIN2S4
www.vishay.com
2
Document Number: 68397
S11-0176-Rev. B, 07-Feb-11
Vishay Siliconix
DG2707
Notes:
a. Signals on S
X
or D
X
, or IN
X
or EN exceeding V+ will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
b. All leads welded or soldered to PC board.
c. Derate 6.6 mW/°C above 70 °C
d. Manual soldering with iron is not recommended for leadless components. The miniQFN-16 is a leadless package. The end of the lead terminal
is exposed copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper lip cannot be
guaranteed and is not required to ensure adequate bottom side solder interconnection.
TRUTH TABLE DG2707 MULTIPLEXER, MINIQFN-16L
Enable Input Select Input On Switches (Pin)
EN (Pin 13) IN2 (Pin 10) IN1 (Pin 3) Description (Pin) Common (Pin)
0 0 0 S5 (Pin 12)
D2 (Pin 15)
0 0 1 S6 (Pin 14)
0 1 0 S7 (Pin 16)
0 1 1 S8 (Pin 1)
0 0 0 S1 (Pin 4)
D1 (Pin 7)
0 0 1 S2 (Pin 6)
0 1 0 S3 (Pin 8)
0 1 1 S4 (Pin 9)
1 X X All Switches are off
Pin 5 N/C
ABSOLUTE MAXIMUM RATINGS (T
A
= 25 °C, unless otherwise noted)
Parameter Limit Unit
Reference to GND
V+ - 0.3 to 5.0
V
EN, IN, D
X
, S
X
a
- 0.3 to (V+ + 0.3)
Current (Any terminal except S
X
or D
X
)30
mAContinuous Current (S
X
or D
X
) ± 300
Peak Current (Pulsed at 1 ms, 10 % Duty Cycle) ± 500
Storage Temperature (D Suffix) - 65 to 150 °C
Thermal Resistance (Package)
b
miniQFN-16 152 °C/W
Power Dissipation (Packages)
b
miniQFN-16
c, d
525 mW
Document Number: 68397
S11-0176-Rev. B, 07-Feb-11
www.vishay.com
3
Vishay Siliconix
DG2707
Notes:
a. Room = 25 °C, Full = as determined by the operating suffix.
b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
c. Typical values are for design aid only, not guaranteed nor subject to production testing.
d. Guarantee by design, not subjected to production test.
e. V
IN
= input voltage to perform proper function.
f. Crosstalk measured between channels.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
SPECIFICATIONS (V+ = 3.15 V)
Parameter Symbol
Test Conditions
Otherwise Unless Specified Temp.
b
Limits
- 40 °C to 85 °C
Unit Min.
d
Typ.
c
Max.
d
Analog Switch
Analog Signal Range
e
V
analog
R
DS(on)
Full 0 V+ V
On Resistance R
DS(on)
V+ = 3.15 V, IS
X
= 10 mA, VD
X
= 1.0 V
Room 2.8 5.5
Full 6
R
ON
Match R
(on)
V+ = 3.15 V, IS
X
= 10 mA, VD
X
= 1.0 V
Room 0.3
R
ON
Resistance Flatness
R
(on)
Flatness V+ = 3.15 V, IS
X
= 10 mA, VD
X
= 0.0 V, 1.0 V
Room 0.6
Channel-Off Leakage Current
I
SX(off)
V+ = 3.6 V, VS
X
= 0.5 V/3 V, VD
X
= 3 V/0.5 V
Room - 5 5
nA
I
DX(off)
Full - 10 10
Channel-On Leakage Current
I
DX(on)
V+ = 3.6 V, VS
X
, VD
X
= 3 V/0.5 V
Room - 10 10
Full - 20 20
Digital Control
Input High Voltage
V
INH
Full
1.65
V
Input Low Voltage
V
INL
0.4
Input Current
I
INL
or I
INH
V
IN
= 0 or V+ - 1 1 µA
Input Capacitance
C
IN
V+ = 3.15, f = 1 MHz 5.1 pF
Dynamic Characteristics
Break-Before-Make Time
t
BBM
VS
X
= 1.5 V, R
L
= 50 , C
L
= 35 pF
Room 1
ns
Full 5
Enable Turn-On Time
t
ON(EN)
Room 20 45
Full 55
Enable Turn-Off Time
t
OFF(EN)
Room 15 35
Full 45
Transition Time
t
TRANS
Room 35 55
Full 65
Charge Injection
d
Q
INJ
C
L
= 1 nF, R
GEN
= 0 , VS
X
= 2 V
Room - 14 pC
Off-Isolation
d
OIRR
V+ = 3.15 V, f = 1 MHz, R
L
= 50 , C
L
= 5 pF
Room
- 70
dB
Crosstalk
d, f
X
TA LK
- 90
Bandwidth
d
BW V+ = 3.15 V, R
L
= 50 , C
L
= 5 pF, - 3 dB
Room 120 MHz
Total Harmonic Distortion
d
THD
V+ = 3.15 V, R
load
= 600 Room 0.02 %
S
X
, D
X
Off Capacitance
d
C
S(off)
V+ = 3.15 V, f = 1 MHz Room
16
pF
CD
X(off)
42
Channel-On Capacitance
d
CD
X(on)
49
Power Supply
Power Supply Range
V+
1.65 4.3 V
Power Supply Current
I+
V
IN
= 0 V or V+ Full 1 µA

DG2707DN-T1-E4

Mfr. #:
Manufacturer:
Vishay / Siliconix
Description:
Multiplexer Switch ICs 3 OMGA Diff 4:1 CMOS MUX
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet