OMO ElectronicOMO Electronic
Expand menu
0 Cart

P3P73U00AG-08-TT

P1-P3P4-P6P7-P9P10-P12
PCS3P73U00A
Rev. 1 | Page 4 of 12 | www.onsemi.com
Switching Characteristics for 3.3 Supply Voltage
Parameter Test Conditions Min Typ Max Unit
FS=0 10 12 27
Input Frequency
FS=1 20 48 70
FS=0 10 12 27
ModOUT
FS=1 20 48 70
MHz
Duty Cycle
1,2
Measured at V
DD
/2 45 50 55 %
Rise Time
1,2
Measured between 20% to 80% 1.1 nS
Fall Time
1,2
Measured between 80% to 20% 0.7 nS
Cycle-to-Cycle Jitter
1,2
Loaded outputs ±150 pS
PLL Lock Time
2
Stable power supply, valid clock presented on XIN / CLKIN pin 3 mS
Notes: 1. All parameters are specified with 10pF loaded outputs.
2. Parameter is guaranteed by design and characterization. Not 100% tested in production.
Electrical Characteristics for 2.5V Supply voltage
Parameter Description Test Conditions Min Typ Max Unit
V
DD
Supply Voltage 2.3 2.5 2.7 V
V
IL
Input LOW Voltage 0.7 V
V
IH
Input HIGH Voltage 1.7 V
I
IL
Input LOW Current V
IN
= 0V -50 µA
I
IH
Input HIGH Current V
IN
= V
DD
50 µA
V
OL
Output LOW Voltage I
OL
= 8mA 0.6 V
V
OH
Output HIGH Voltage I
OH
= -8mA 1.8 V
I
CC
Static Supply Current XIN / CLKIN pulled to GND 500 µA
FS=0; @ 12MHz 5
I
DD
Dynamic Supply Current Unloaded outputs
FS=1; @ 48MHz 8
mA
Z
o
Output Impedance 40 :
Switching Characteristics for 2.5V Supply Voltage
Parameter Test Conditions Min Typ Max Unit
FS=0 10 12 20
Input Frequency
FS=1 20 48 60
FS=0 10 12 20
ModOUT
FS=1 20 48 60
MHz
Duty Cycle
1,2
Measured at V
DD
/2 45 50 55 %
Rise Time
1,2
Measured between 20% to 80% 1.6 nS
Fall Time
1,2
Measured between 80% to 20% 0.8 nS
Cycle-Cycle Jitter
1,2
Loaded outputs ±200 pS
PLL Lock Time
2
Stable power supply, valid clock presented on XIN / CLKIN pin 3 mS
Notes: 1. All parameters are specified with 10pF loaded outputs.
2. Parameter is guaranteed by design and characterization. Not 100% tested in production.
PCS3P73U00A
Rev. 1 | Page 5 of 12 | www.onsemi.com
R
R1 = 510
Cr
y
stal
C1 = 27 pF
C2 = 27 pF
Fig. 1:
Typical Crystal Interface Circuit
Note: For AC Coupled Interface refer to Application Brief: CT100801.
Typical Crystal Specifications
Fundamental AT cut parallel resonant crystal
Nominal frequency 48MHz
Frequency tolerance ±50ppm or better at 25°C
Operating temperature range -25°C to +85°C
Storage temperature -40°C to +85°C
Load capacitance 18pF
Shunt capacitance 7pF maximum
ESR 25 :
R
Compliance
The value of the compliance resistor, R
Compliance
sets the
USB2.0 signaling rate (frequency) deviation to 1000ppm
peak-to-peak (+/-500ppm). It causes a -4dB peak power
EMI reduction at the 480MHz fundamental USB2.0
frequency. Higher harmonics are reduced more.
If the R
Compliance
is set to a lower value than its compliance
limit, it will set the USB2.0 signaling rate (frequency)
deviation to above 1000ppm peak-to-peak. For settings
above 1000ppm the USB2.0 compliance pass/fail
becomes gradually intermittent. USB2.0 functionality is
maintained upto 3000ppm peak-to-peak signaling rate
(frequency) deviation. The EMI tradeoff in the system is
attenuation/compliance. While fully functional (and
compliant intermittent) the 2000ppm frequency deviation
can provide -7dB of EMI attenuation at the 480MHz
fundamental.
PCS3P73U00A
Rev. 1 | Page 6 of 12 | www.onsemi.com
Deviation Vs Resistance (MR=0)
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
0 5 10 15 20 25 30 35 40
Resistance (KOhms)
Pk-Pk Deviation (PPM)
12MHz_FS=0
15MHz_FS=0
24MHz_FS=0
24MHz_FS=1
25MHz_FS=0
25MHz_FS=1
30MHz_FS=1
48MHz_FS=1
USB 2.0 Compliance
480MHz Fundamental Frequency Attenuation[dB
]
-4dB
-7dB
-2dB
Deviation Vs Resistance (MR=1)
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
0 102030405060708090100
Resistance (KOhms)
Pk-Pk Deviation (PPM)
12MHz_FS=0
15MHz_FS=0
24MHz_FS=0
24MHz_FS=1
25MHz_FS=0
25MHz_FS=1
30MHz_FS=1
48MHz_FS=1
USB Compliance
480MHz Fundamental Frequency Attenuation[dB
]
-4dB
-7dB
-2dB
SSEXTR Resistance Table for USB2.0 compliance (R
Compliance
)
VDD = 3.3V; MR = 0
Frequency
(MHz)
FS
(MHz)
SSEXTR
1
Resistance (K)
12 0 10
15 0 8.87
0 6.81
24
1 13.7
0 6.98
25
1 13.7
30 1 12.1
48 1 10
VDD = 3.3V; MR = 1
Frequency
(MHz)
FS
(MHz)
SSEXTR
1
Resistance (K)
12 0 17.8
15 0 13
0 6.49
24
1 39.2
0 6.49
25
1 35.7
30 1 29.4
48 1 19.1
VDD = 2.5V; MR = 0
Frequency
(MHz)
FS
(MHz)
SSEXTR
1
Resistance (K)
12 0 10
15 0 8.87
24 1 13.7
25 1 13.7
30 1 12.1
48
1 10
VDD = 2.5V; MR = 1
Frequency
(MHz)
FS
(MHz)
SSEXTR
1
Resistance (K)
12 0 17.8
15 0 13
24
1 39.2
25
1 35.7
30 1 29.4
48 1 19.1
Fig. 3: Deviation Vs Resistance
for USB 2.0 Com
Fig. 2: Deviation Vs Resistance
for USB 2.0 Com
p
liance
(
MR=1
)
p
liance
(
MR=0
)
Note: 1. Standard 1% tolerance Resistors.
Device to Device variation of Deviation is ±10%.
P1-P3P4-P6P7-P9P10-P12

P3P73U00AG-08-TT

Mfr. #:
Buy P3P73U00AG-08-TT
Manufacturer:
ON Semiconductor
Description:
Clock Generators & Support Products 10-70MHZ 2.5V/3.3V EMI
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet