PDF: 09005aef80e935cd/Source: 09005aef80e934a6 Micron Technology, Inc., reserves the right to change products or specifications without notice.
HTF18C64_128_256x72D.fm - Rev. E 2/07 EN
11 ©2003 Micron Technology, Inc. All rights reserved.
512MB, 1GB, 2GB (x72, ECC, DR) 240-Pin DDR2 SDRAM RDIMM
Electrical Specifications
Notes: 1. Value calculated as one module rank in this operating condition; all other module ranks in
I
DD2P (CKE LOW) mode.
2. Value calculated reflects all module ranks in this operating condition.
Table 13: DDR2 IDD Specifications and Conditions (Die Revision E) – 2GB
Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the
1Gb (128 Meg x 8) component data sheet
Parameter/Condition Symbol
-80E
-800
-667 -53E -40E Units
Operating one bank active-precharge current:
t
CK =
t
CK (IDD),
t
RC =
t
RC (IDD),
t
RAS =
t
RAS MIN (IDD); CKE is HIGH, S# is HIGH between valid
commands; Address bus inputs are switching; Data bus inputs are switching
IDD0
1
963 873 783 693 mA
Operating one bank active-read-precharge current: I
OUT = 0mA;
BL = 4, CL = CL (IDD), AL = 0;
t
CK =
t
CK (IDD),
t
RC =
t
RC (IDD),
t
RAS =
t
RAS MIN
(IDD),
t
RCD =
t
RCD (IDD); CKE is HIGH, S# is HIGH between valid commands;
Address bus inputs are switching; Data pattern is same as I
DD4W
I
DD1
1
1,053 963 918 783 mA
Precharge power-down current: All device banks idle;
t
CK =
t
CK (IDD);
CKE is LOW; Other control and address bus inputs are stable; Data bus
inputs are floating
I
DD2P
2
126 126 126 126 mA
Precharge quiet standby current: All device banks idle;
t
CK =
t
CK (IDD);
CKE is HIGH, S# is HIGH; Other control and address bus inputs are stable;
Data bus inputs are floating
IDD2Q
2
1,170 990 738 630 mA
Precharge standby current: All device banks idle;
t
CK =
t
CK (IDD); CKE is
HIGH, S# is HIGH; Other control and address bus inputs are switching; Data
bus inputs are switching
IDD2N
2
1,260 1,080 810 720 mA
Active power-down current: All device banks open;
t
CK =
t
CK (IDD); CKE is LOW; Other control and address
bus inputs are stable; Data bus inputs are floating
Fast PDN exit
MR[12] = 0
I
DD3P
2
810 720 630 630 mA
Slow PDN exit
MR[12] = 1
252 252 252 252 mA
Active standby current: All device banks open;
t
CK =
t
CK (IDD),
t
RAS =
t
RAS MAX (IDD),
t
RP =
t
RP (IDD); CKE is HIGH, S# is HIGH between
valid commands; Other control and address bus inputs are switching; Data
bus inputs are switching
I
DD3N
2
1,350 1,260 990 810 mA
Operating burst write current: All device banks open; Continuous burst
writes; BL = 4, CL = CL (IDD), AL = 0;
t
CK =
t
CK (IDD),
t
RAS =
t
RAS MAX (IDD),
t
RP =
t
RP (IDD); CKE is HIGH, S# is HIGH between valid commands; Address
bus inputs are switching; Data bus inputs are switching
I
DD4W
2
1,728 1,503 1,233 1,053 mA
Operating burst read current: All device banks open; Continuous burst
reads; IOUT = 0mA; BL = 4, CL = CL (IDD), AL = 0;
t
CK =
t
CK (IDD),
t
RAS =
t
RAS MAX (IDD),
t
RP =
t
RP (IDD); CKE is HIGH, S# is HIGH between
valid commands; Address bus inputs are switching; Data bus inputs are
switching
I
DD4R
2
1,773 1,503 1,368 1,053 mA
Burst refresh current:
t
CK =
t
CK (IDD); REFRESH command at every
t
RFC
(I
DD) interval; CKE is HIGH, S# is HIGH between valid commands; Other
control and address bus inputs are switching; Data bus inputs are switching
I
DD5
2
5,040 4,680 4,500 3,960 mA
Self refresh current: CK and CK# at 0V; CKE ≤ 0.2V; Other control and
address bus inputs are floating; Data bus inputs are floating
I
DD6
2
126 126 126 126 mA
Operating bank interleave read current: All device banks interleaving
reads; I
OUT = 0mA; BL = 4, CL = CL (IDD), AL =
t
RCD (IDD) - 1 x
t
CK (IDD);
t
CK =
t
CK (IDD),
t
RC =
t
RC (IDD),
t
RRD =
t
RRD (IDD),
t
RCD =
t
RCD (IDD); CKE is
HIGH, S# is HIGH between valid commands; Address bus inputs are stable
during deselects; Data bus inputs are switching
I
DD7
1
3,078 2,763 2,673 2,403 mA
