OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

T356D226K006AS

P1-P3P4-P6P7-P9P10-P12P13-P13
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2043_T35X • 3/27/2018 10
Tantalum Through-Hole Capacitors – Radial Dipped
T350, T351, T352, T353, T354, T355 and T356 UltraDip II Polar
Optimum Solder Wave Prole
Mounting
All encased capacitors will pass the Resistance to Soldering Heat Test of MIL–STD–202, Method 210, Condition C. This test
simulates wave solder of topside board mount product. This demonstration of resistance to solder heat is in accordance
with what is believed to be the industry standard. More severe treatment must be considered reective of an improper
soldering process. The above gure is a recommended solder wave prole for both axial and radial leaded solid tantalum
capacitors.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2043_T35X • 3/27/2018 11
Tantalum Through-Hole Capacitors – Radial Dipped
T350, T351, T352, T353, T354, T355 and T356 UltraDip II Polar
Capacitor Marking
Polarity
Polarity
Stripe (+)
Voltage
Rating
Capacitance
(pF code)
KEMET
Trademark
Date
Code
Storage
Tantalum molded radial/axial capacitors should be stored in normal working environments. KEMET recommends that
maximum storage temperature not exceed 40°C and maximum storage humidity not exceed 60°C RH. Storage at high
temperature may cause a small, temporary increase in leakage current (measured under standard conditions), but the
original value is usually restored within a few minutes after application of rated voltage. Storage at high humidity may
increase capacitance and dissipation factor. Solderability will be degraded by exposure to high temperatures, high humidity,
corrosive atmospheres, and long term storage. For optimized solderability capacitors stock should be used promptly,
preferably within three years of receipt.
Tape & Reel Packaging Information
Table 2 – Packaging Quantity
Case Size
Standard Bulk
Quantity
Standard Reel
Quantity
Reel C-Spec
Ammo Pack
Quantity
A 1,000 1,500
C-7301/7303
2,500
B 1,000 1,500 2,500
C 1,000 1,500 2,500
D 1,000 1,000 2,000
E 1,000 1,000 2,000
F 500 1,000 1,500
G 500 1,000 1,500
H 500 800 1,500
J 100 800 800
K 100 500 800
L, M 100 500 Pending 500
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2043_T35X • 3/27/2018 12
Tantalum Through-Hole Capacitors – Radial Dipped
T350, T351, T352, T353, T354, T355 and T356 UltraDip II Polar
Figure 1
P
0
D
0
L
1
T
d
F
P
P
2
W
L
A
1
3
W
2
W
2
T
0
P
1
W
0
A
H
H
1
H
0
W
1
1
2
3
T396/98*
T350/51*
T352/53/56**
4
T354#
5
T355+
1 2
Carrier
Tape
1 mm
Maximum
(0.039”)
∆H
Dimension Symbol
Nominal
mm (inch)
Tolerance
mm (inch)
Body Height (1) A 17.0 (0.67) Maximum
Body Width (1) A
1
15.24 (0.600) Maximum
Sprocket Hole Diameter D
0
4.0 (0.157) ±0.3 (±0.012)
Lead Diameter d 0.51 (0.020) 0.64 (0.025) ±0.05 (±0.002)
Lead Center (4) F See Note Below
Component Base to Tape Center (4) H
C-7301
16.0 (0.630)
C-7303
18.0 (0.709)
C-7301
±0.5 (±0.02)
C-7303
Minimum
Lead Standoff Height H
0
C-7301
16.0 (0.630)
C-7303
18.0 (0.709)
C-7301
±0.5 (±0.02)
C-7303
Minimum
Component Height Above Tape Center H
1
32.25 (1.270) Maximum
Component Alignment Front to Rear ΔH 0 1.0 (0.039)
Cut Out Length L 11.0 (0.433) Maximum
Lead Protrusion L
1
1.0 (0.039) Maximum
Component Pitch (5) P 12.7 (0.500) ±1.0 (±0.039)
Sprocket Hole Pitch (2) P
0
12.7 (0.500) ±0.03 (±0.012)
Sprocket Hole Center to Lead Center (3) (4) P
1
See Note Below ±0.7 (±0.028)
Sprocket Hole Center to Component Center (5)
P
2
See Note Below
Body Thickness T
0
10.2 (0.400) Maximum
Total Tape Thickness T 0.7 (0.28) ±0.02 (±0.008)
Carrier Tape Width W 18.0 (0.709) +1.0/−0.5 (+0.039/−0.020)
Hold-Down Tape Width W
0
15 mm (0.561) 6 mm (0.236) +1.0/−0.8 (+0.039/−0.031
Sprocket Hole Location W
1
9.0 (0.354) +0.075/−0.5 (+0.030/−0.020)
Hold-Down Tape Location W
2
12.0 (0.472) Maximum
Notes:
(1) See Dimensions table for specic values per case size.
(2) Cumulative pitch error ± 1.0 mm (0.039) maximum in 20
consecutive sprocket hole locations.
(3) Measured at bottom of standoff.
(4) P
1
and F measured at egress from carrier tape.
(5) P and P2 measured at egress from carrier tape.
* Lead spacings are 2.5 mm (0.098") center to center (T350 A-H)
** Lead spacings are 5.0 mm (0.197") center to center
# Lead spacings are 6.35 mm (0.25") center to center
+ Lead spacings are 3.18 mm (0.125") center to center
F Dimensions: P
1
Dimensions:
0.100" ±0.015 Lead Spacing
0.125" ±0.015 0.100" – 0.200 ±0.028"
0.200" ±0.015 0.125" – 0.187 ±0.028"
0.250" ±0.015" 0.200" – 0.150 ±0.028"
0.100" ±0.015 (3 leaded) 0.250" – 0.125 ±0.028"
0.100" – 0.100 ±0.028" ( 3 leaded)
P1-P3P4-P6P7-P9P10-P12P13-P13

T356D226K006AS

Mfr. #:
Buy T356D226K006AS
Manufacturer:
Description:
Tantalum Capacitors - Solid Leaded 6volts 22uF 10% D CASE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet