OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TLP105(F)

P1-P3P4-P6
TLP105
2015-10-16
1
TOSHIBA PHOTOCOUPLER GaAℓAs IRED & PHOTO-IC
TLP105
Isolated bus drivers
High-speed line receivers
Microprocessor system interfaces
The Toshiba TLP105 consists of a GaAℓAs light emitting diode optically
coupled to a high-gain, high-speed photodetector.
The TLP105 is housed in a 6-pin MFSOP.
With a totem-pole output, the TLP105 is capable of both sinking and
sourcing current.
The TLP105 has an internal Faraday shield, which provides a guaranteed
common-mode transient immunity of ±10 kV/μs.
The TLP105 has a noninverting output. An inverting-output version, the
TLP108, is also available.
Buffer logic type (totem-pole output)
Guaranteed Performance Over Temperature: −40 to 100°C
Power Supply Voltage: 4.5 to 20 V
Input Threshold Current: I
FLH
=1.6 mA (max)
Switching Time (t
pLH
/t
pHL
): 250 ns (max)
Common mode transient immunity: ±10 kV/μs
Isolation Voltage: 3750 Vrms
UL approved : UL1577, File No.E67349
c-UL approved :CSA Component Acceptance Service
No. 5A, File No.E67349
Option (V4) VDE approved : DIN EN60747-5-5 (Note)
Note : When a EN60747-5-5 approved type is needed,
Please designate “Option(V4)”
Truth Table
Input LED Tr1 Tr2 Output
H
ON
ON
OFF
H
L
OFF
OFF
ON
L
JEDEC
TOSHIBA
Weight: 0.09 g (typ.)
Unit: mm
Start of commercial production
2008-05
Pin Configuration (top View)
Schematic
1:ANODE
3:CATHODE
4:GND
5:V
O
(Output)
6:V
CC
V
CC
GND
SHIELD
1
3
4
5
6
V
CC
V
O
GND
I
CC
I
O
6
5
4
SHIELD
3－
1＋
I
F
V
F
Tr1
Tr2
0.1 µF bypass capacitor must be
connected between pin 6 and 4.
TLP105
2015-10-16
2
Recommended Operating Conditions
CHARACTERISTIC
SYMBOL
MIN
TYP.
MAX
UNIT
Input Current, ON
I
F(ON)
2
―
10
mA
Input Voltage, OFF
V
F(OFF)
0
―
0.8
V
Supply Voltage*
V
CC
4.5
―
20
V
Operating Temperature T
opr
-40 ― 100 °C
Fan-out (TTL Load)
N
―
―
4
―
* This item denotes operating range, not meaning of recommended operating conditions.
Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
Absolute Maximum Ratings (Ta = 25°C)
CHARACTERISTIC
SYMBOL
RATING
UNIT
LED
Forward Current
I
F
20
mA
Forward Current Derating (Ta ≥ 83°C)
Δ
IF/°C
-0.48
mA/°C
Peak Transient Forward Current (Note1)
I
FPT
1
A
Input Power Dissipation
P
D
40
mW
Reverse Voltage
V
R
5
V
DETECTOR
Output Current 1 (Ta
≤
25°C)
I
O1
25/-15
mA
Output Current 2 (Ta ≤
100°C)
I
O2
5/-5
mA
Output Current Derating (Ta ≥ 25
°
C)
Δ
IO1/°C
-0.26/-0.13
mA/°C
Peak Output Current (Note2) I
OP
50/-50 mA
Output Voltage
V
O
-0.5 to 20
V
Output Power Dissipation
P
O
75
mW
Supply Voltage
V
CC
-0.5 to 20
V
Operating Temperature Range T
opr
−40 to 100 °C
Storage Temperature Range
T
stg
−55 to 125
°C
Lead Solder Temperature (10 s)
T
sol
260
°C
Isolation Voltage
(AC, 60 s, R.H. ≤ 60%, Ta = 25°C) (Note3)
BV
s
3750 V
rms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if
the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width ≤ 1 μs, 300 pps.
Note 2: Pulse width ≤ 5 μs, duty cycle ≤ 0.025
Note 3: Device considered a two terminal device: pins 1 and 3 shorted together and pins 4, 5 and 6 shorted together.
TLP105
2015-10-16
3
Electrical Characteristics
(Unless otherwise specified, Ta = -40 to 100°C, V
CC
= 4.5 to 20 V)
CHARACTERISTIC SYMBOL
TEST
CIRCUIT
CONDITION MIN TYP. MAX UNIT
Input Forward Voltage
V
F
―
I
F
=10 mA, Ta=25°C
1.45 1.57 1.75 V
Temperature Coefficient
of Forward Voltage
ΔV
F
/Δ Ta ― I
F
=10 mA ― -2.0 ― mV/°C
Input Reverse Current
I
R
―
V
R
=5 V, Ta=25°C
― ― 10 μA
Input Capacitance
C
T
―
V=0, f=1 MHz, Ta=25°C
― 100 - pF
Logic Low Output Voltage V
OL
1 I
OL
=3.5 mA, V
F
=0.8 V ― 0.2 0.6 V
Logic High Output Voltage V
OH
2
I
OH
=−2.6 mA,
I
F
=5 mA
V
CC
=4.5 V
2.7 4.0
―
V
V
CC
=20 V
17.4 19.0
―
Logic Low Supply Current I
CCL
3 V
F
=0 V
V
CC
=20 V ― ― 3.0
mA
V
CC
=5.5 V ― ― 3.0
Logic High Supply Current I
CCH
4 I
F
=5 mA
V
CC
=20 V ― ― 3.0
mA
V
CC
=5.5 V ― ― 3.0
Logic Low Short Circuit
Output Current (Note 1)
I
OSL
5 V
F
=0 V
V
CC
=V
O
=5.5 V 15
80
―
mA
V
CC
=V
O
=20 V 20
90
―
Logic High Short Circuit
Output Current (Note 1)
I
OSH
6
I
F
=5 mA
V
O
=GND
V
CC
=5.5 V −5
−15
―
mA
V
CC
=20 V −10
−20
―
Input Current Logic High
Output
I
FLH
― I
O
=-2.6 mA, V
O
>2.4 V ― 0.4 1.6 mA
Input Voltage Logic Low
Output
V
FHL
― I
O
=3.5 mA, V
O
<0.4 V 0.8 ― ― V
Input Current Hysteresis I
HYS
―
V
CC
=5 V
― 0.05 ― mA
*All typical values are at Ta=25°C
Note 1: Duration of output short circuit time should not exceed 10 ms.
Note : A ceramic capacitor (0.1 μA) should be connected from pin 6 to pin 4 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypassing may impair the switching property. The total lead
length between capacitor and coupler should not exceed 1 cm.
Isolation Characteristics
(Ta = 25°C)
Characteristic Symbol Test Condition Min Typ. Max Unit
Capacitance input to output C
S
V
S
= 0, f = 1 MHz ― 0.8 ― pF
Isolation resistance R
S
R.H. ≤ 60%, V
S
= 500 V 1×10
12
10
14
― Ω
Isolation voltage BV
S
AC,60 s 3750 ― ―
V
rms
AC,1 s, in oil ― 10000 ―
DC,60 s, in oil ― 10000 ― V
dc
P1-P3P4-P6

TLP105(F)

Mfr. #:
Buy TLP105(F)
Manufacturer:
Toshiba
Description:
High Speed Optocouplers IC3 STATE OUTPUT
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet