PAM2319
Document number: DSxxxxx Rev. 1 - 1
10 of 12
www.diodes.com
November 2012
© Diodes Incorporated
PAM2319
A
Product Line o
f
Diodes Incorporated
Application Information (cont.)
Short Circuit Protection
Channel 1:
The swich peak current is limited cycle-by-cycle to a typical vaule in the event of an output voltage short circuit. The device operates with a
frequency of 1MHz and minimum duty clycle. Therefore the average input current is typical 350mA (V
IN
= 3.3V).
Channel 2:
When the converter output is shorted or the device is overloaded, each high-side MOSFET current-limit event (3A typ) turns off the high-side
MOSFET and turns on the low-side MOSFET. An internal counter is used to count the each current-limit event. The counter is reset after
consecutive high-side MOSFETs turn on without reaching current limit. If the current-limit condition persists, the counter fills up. The control logic
then stops both high-side and lowside MOSFETs and waits for a hiccup period, before attemping a new soft-start sequence. The counter bits is
decided by V
FB
voltage. If V
FB
0 2, the counter is 3-bit counter; if VFB > 0.2 the counter is 6-bit counter. The typical hicuup made duty cycle is
1.7%. The hiccup mode is disable during soft-start time.
PCB Layout Check List
When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the PAM2319. Check the following
in your layout:
1. The input capacitor should be close to IC as close as possible.
2. Minimize the switching loop area to avoid excessive switching noise.
3. Two parts GND should be separately layout to avoid disturbing by each other.
4. Must put a small decoupling capacitor between Vin2 Pin and AGND2 Pin.
5. Vo2 output capacitor should be close to output connector to minimize PCB t race resistance affect on ripple voltage. Recommend use two
output capacitor, one close to inductor and IC, another close to output connector.
6. PGND1 Pin should not directly connect to the thermal pad (PGND), it should connect to input capacitor GND then to other GND.
7. AGND should connect to PGND at input capacitor GND.
8. For the good thermal dissipation, PAM2316 has a heat dissipate pad in the bottom side, it should be soldered to PCB surface. For the copper
area can't be large in the component side, so we can use multiple vias connect to other side of the PCB.
9. Avoid using vias in the high-current paths. If vias are unavoidable, use multiple vias in parallel to reduce resistance and inductance.
Ordering Information
Part Number Part Marking Package Type Standard Package
PAM2319AYAA
BNAA
XXXYW
W-DFN3x3-12L 3000 Units/Tape & Reel
PAM2319
Document number: DSxxxxx Rev. 1 - 1
11 of 12
www.diodes.com
November 2012
© Diodes Incorporated
PAM2319
A
Product Line o
f
Diodes Incorporated
Marking Information
Package Outline Dimensions (All dimensions in mm.)
W-DFN3x3-12
PAM2319
Document number: DSxxxxx Rev. 1 - 1
12 of 12
www.diodes.com
November 2012
© Diodes Incorporated
PAM2319
A
Product Line o
f
Diodes Incorporated
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2012, Diodes Incorporated
www.diodes.com

PAM2319AYAA

Mfr. #:
Manufacturer:
Diodes Incorporated
Description:
Switching Voltage Regulators DUAL HI-EFF PWM SD DC/DC CNVTR
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet