AOT2608L/AOB2608L
Symbol Min Typ Max Units
BV
DSS
60 V
V
DS
=60V, V
GS
=0V 1
T
J
=55°C 5
I
GSS
±100 nA
V
GS(th)
Gate Threshold Voltage
2.6 3.1 3.6 V
I
D(ON)
180 A
6.6 8
T
J
=125°C 11.4 14
g
FS
75 S
V
SD
0.72 1 V
I
S
72 A
C
iss
2995 pF
C
oss
270 pF
C
rss
10.5 pF
R
g
0.3 0.6 0.9 Ω
Q
g
38.5 55 nC
Q
gs
14 nC
Q
gd
3.5 nC
t
D(on)
15 ns
V
GS
=10V, I
D
=20A
TO263
mΩ
7.66.3
Maximum Body-Diode Continuous Current
Input Capacitance
Output Capacitance
Turn-On DelayTime
DYNAMIC PARAMETERS
Gate resistance
V
GS
=0V, V
DS
=0V, f=1MHz
Total Gate Charge
V
GS
=10V, I
D
=20A
Gate Source Charge
Gate Drain Charge
SWITCHING PARAMETERS
R
DS(ON)
Static Drain-Source On-Resistance
Diode Forward Voltage
V
GS
=10V, V
DS
=30V, I
D
=20A
Reverse Transfer Capacitance
V
GS
=0V, V
DS
=30V, f=1MHz
mΩ
I
S
=1A,V
GS
=0V
V
DS
=5V, I
D
=20A
TO220
Forward Transconductance
V
DS
=V
GS，
I
D
=250µA
Electrical Characteristics (T
J
=25°C unless otherwise noted)
STATIC PARAMETERS
Parameter Conditions
I
DSS
µA
Zero Gate Voltage Drain Current
Drain-Source Breakdown Voltage
I
D
=250µA, V
GS
=0V
V
DS
=0V, V
GS
=±20V
Gate-Body leakage current
On state drain current
V
GS
=10V, V
DS
=5V
r
t
D(off)
25 ns
t
f
2.5 ns
t
rr
24 ns
Q
rr
115
nC
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
I
F
=20A, dI/dt=500A/µs
Body Diode Reverse Recovery Charge
Body Diode Reverse Recovery Time
I
F
=20A, dI/dt=500A/µs
Turn-Off DelayTime
GS
DS
L
R
GEN
=3Ω
Turn-Off Fall Time
A. The value of R
θJA
is measured with the device mounted on 1in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The
Power dissipation P
DSM
is based on R
θJA
and the maximum allowed junction temperature of 150°C. The value in any given application
depends on the user's specific board design, and the maximum temperature of 175°C may be used if the PCB allows it.
B. The power dissipation P
D
is based on T
J(MAX)
=175°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature T
J(MAX)
=175°C. Ratings are based on low frequency and duty cycles to keep
initial T
J
=25°C.
D. The R
θJA
is the sum of the thermal impedance from junction to case R
θJC
and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedance which is measured with the device mounted to a large heatsink,
assuming a maximum junction temperature of T
J(MAX)
=175°C. The SOA curve provides a single pulse rating.
G. The maximum current limited by package.
H. These tests are performed with the device mounted on 1 in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C.
Rev 1 : Mar. 2012 www.aosmd.com Page 2 of 6
