74AHC_AHCT1G66_4 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 04 — 18 December 2008 4 of 17
NXP Semiconductors
74AHC1G66; 74AHCT1G66
Single-pole single-throw analog switch
[1] To avoid drawing V
CC
current out of pin Z, when switch current flows in pin Y, the voltage drop across the bidirectional switch must not
exceed 0.4 V. If the switch current flows into pin Z, no V
CC
current will flow out of terminal Y. In this case there is no limit for the voltage
drop across the switch, but the voltage at pins Yand Z may not exceed V
CC
or GND.
[2] Applies to control signal levels.
10. Static characteristics
T
amb
ambient temperature −40 +25 +125 −40 +25 +125 °C
∆t/∆V input transition rise and
fall rate
V
CC
= 3.3 ± 0.3 V
[2]
- - 100 - - - ns/V
V
CC
= 5.0 ± 0.5 V
[2]
- - 20 - - 20 ns/V
Table 6. Recommended operating conditions
…continued
Voltages are referenced to GND (ground = 0 V).
[1]
Symbol Parameter Conditions 74AHC1G66 74AHCT1G66 Unit
Min Typ Max Min Typ Max
Table 7. Static characteristics
Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions 25 °C −40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max Min Max Min Max
74AHC1G66
V
IH
HIGH-level
input voltage
V
CC
= 2.0 V 1.5 - - 1.5 - 1.5 - V
V
CC
= 3.0 V 2.1 - - 2.1 - 2.1 - V
V
CC
= 5.5 V 3.85 - - 3.85 - 3.85 - V
V
IL
LOW-level
input voltage
V
CC
= 2.0 V - - 0.5 - 0.5 - 0.5 V
V
CC
= 3.0 V - - 0.9 - 0.9 - 0.9 V
V
CC
= 5.5 V - - 1.65 - 1.65 - 1.65 V
I
I
input leakage
current
V
I
= 5.5 V or GND;
V
CC
= 5.5 V
- - 0.1 - 1.0 - 2.0 µA
I
S(OFF)
OFF-state
leakage
current
Y or Z; V
CC
= 5.5 V;
see
Figure 4
- - 0.1 - 1.0 - 4.0 µA
I
S(ON)
ON-state
leakage
current
Y or Z; V
CC
= 5.5 V;
see
Figure 5
- - 0.1 - 1.0 - 4.0 µA
I
CC
supply current E, Y or Z = V
CC
or GND;
V
CC
= 5.5 V
- - 1.0 - 10 - 40 µA
C
I
input
capacitance
E input - 2.0 10 - 10 - 10 pF
C
S(ON)
ON-state
capacitance
Y or Z input or output - 4.0 10 - 10 - 10 pF
74AHCT1G66
V
IH
HIGH-level
input voltage
V
CC
= 4.5 V to 5.5 V 2.0 - - 2.0 - 2.0 - V
V
IL
LOW-level
input voltage
V
CC
= 4.5 V to 5.5 V - - 0.8 - 0.8 - 0.8 V
I
I
input leakage
current
V
I
= 5.5 V or GND;
V
CC
= 5.5 V
- - 0.1 - 1.0 - 2.0 µA
