4
FN8157.6
August 14, 2015
)
Power Up and Down Requirements
The are no restrictions on the power-up or power-down conditions of V
CC
and the voltages applied to the potentiometer pins
provided that V
CC
is always more positive than or equal to V
H
, V
L
, and V
W
, i.e., V
CC
V
H
, V
L
, V
W
. The V
CC
ramp rate spec is
always in effect.
NOTES:
1. Absolute Linearity is utilized to determine actual wiper voltage versus expected voltage = (V
w(n)
(actual)–V
w(n)
(expected)) = ±1 Ml Maximum.
2. Relative Linearity is a measure of the error in step size between
taps = V
W
(n+1)
– [V
w(n)
+ Ml] = ±0.2 Ml.
3. 1 Ml = Minimum Increment = R
TOT
/31.
4. Typical values are for T
A
= +25°C and nominal supply voltage.
5. This parameter is periodically sampled and not 100% tested.
Absolute Maximum Ratings Operating Conditions
Temperature under bias . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on CS
, INC, U/D, V
H
, V
L
and
V
CC
with respect to V
SS
. . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
V = |V
H
–V
L
| . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V
Lead temperature (soldering 10s) . . . . . . . . . . . . . . . . . . . . . +300°C
I
W
(10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±7.5mA
Temperature Range
Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage (V
CC
)
X9015. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±10%
X9015-2.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Potentiometer Specifications Over recommended operating conditions unless otherwise stated
SYMBOL PARAMETER TEST CONDITIONS/NOTES MIN. TYP. MAX. UNIT
R
TOTAL
End to End Resistance Variation –20 +20 %
V
VH
V
H
/R
H
Terminal Voltage 0 V
CC
V
V
VL
V
L
/R
L
Terminal Voltage 0 V
CC
V
Power Rating R
TOTAL
1k 10 mW
R
W
Wiper Resistance I
W
= 1mA, V
CC
= 5V 200 400
R
W
Wiper Resistance I
W
= 1mA, V
CC
= 2.7V 400 1000
I
W
Wiper Current -3.75 3.75 mA
Noise Ref: 1kHz -120 dBV
Resolution 3%
Absolute Linearity (Note 1) V
w(n)(actual)
–V
w(n)(expected)
-1 +1 MI (Note 3)
Relative Linearity (Note 2) V
w(n+1)
–[V
w(n)+MI
] -0.2 +0.2 MI (Note 3)
R
TOTAL
Temperature Coefficient ±300 ppm/°C
Ratiometric Temperature Coefficient ±20 ppm/°C
C
H
/C
L
/C
W
Potentiometer Capacitances See circuit #3 10/10/25 pF
X9015