MC74HC4066A
http://onsemi.com
3
MAXIMUM RATINGS
Symbol Parameter Value Unit
V
CC
Positive DC Supply Voltage (Referenced to GND) – 0.5 to + 14.0 V
V
IS
Analog Input Voltage (Referenced to GND) – 0.5 to V
CC
+ 0.5 V
V
in
Digital Input Voltage (Referenced to GND) – 0.5 to V
CC
+ 0.5 V
I DC Current Into or Out of Any Pin ± 25 mA
P
D
Power Dissipation in Still Air, SOIC Package†
TSSOP Package†
500
450
mW
T
stg
Storage Temperature – 65 to + 150 °C
T
L
Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP, SOIC or TSSOP Package)
260
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
†Derating − SOIC Package: – 7 mW/°C from 65° to 125°C
TSSOP Package: − 6.1 mW/°C from 65° to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Max Unit
V
CC
Positive DC Supply Voltage (Referenced to GND) 2.0 12.0 V
V
IS
Analog Input Voltage (Referenced to GND) GND V
CC
V
V
in
Digital Input Voltage (Referenced to GND) GND V
CC
V
V
IO
* Static or Dynamic Voltage Across Switch − 1.2 V
T
A
Operating Temperature, All Package Types –55 + 125 °C
t
r
, t
f
Input Rise and Fall Time, ON/OFF Control
Inputs (Figure 10) V
CC
= 2.0 V
V
CC
= 3.0 V
V
CC
= 4.5 V
V
CC
= 9.0 V
V
CC
= 12.0 V
0
0
0
0
0
1000
600
500
400
250
ns
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
*For voltage drops across the switch greater than 1.2 V (switch on), excessive V
CC
current may be drawn; i.e., the current out of the switch may
contain both V
CC
and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC ELECTRICAL CHARACTERISTIC Digital Section (Voltages Referenced to GND)
Symbol Parameter Test Conditions
V
CC
V
Guaranteed Limit
Unit
– 55 to
25°C
v 85°C
v 125°C
V
IH
Minimum High−Level Voltage
ON/OFF Control Inputs
R
on
= Per Spec 2.0
3.0
4.5
9.0
12.0
1.5
2.1
3.15
6.3
8.4
1.5
2.1
3.15
6.3
8.4
1.5
2.1
3.15
6.3
8.4
V
V
IL
Maximum Low−Level Voltage
ON/OFF Control Inputs
R
on
= Per Spec 2.0
3.0
4.5
9.0
12.0
0.5
0.9
1.35
2.7
3.6
0.5
0.9
1.35
2.7
3.6
0.5
0.9
1.35
2.7
3.6
V
I
in
Maximum Input Leakage Current
ON/OFF Control Inputs
V
in
= V
CC
or GND 12.0 ± 0.1 ± 1.0 ± 1.0
A
I
CC
Maximum Quiescent Supply Current
(per Package)
V
in
= V
CC
or GND
V
IO
= 0 V
6.0
12.0
2
4
20
40
40
160
A
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V
in
and
V
out
should be constrained to the
range GND v (V
in
or V
out
) v V
CC
.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V
CC
).
Unused outputs must be left open.
I/O pins must be connected to a
properly terminated line or bus.
