12
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8).
2. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8).
3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8).
4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8).
5. CURRENT TRANSFER RATIO in percent is dened as the ratio of output collector current, I
O
, to the forward LED input current, I
F
, times 100.
6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
CM
/dt on the leading edge of the common
mode pulse signal, V
CM
, to assure that the output will remain in a Logic High state (i.e., V
O
> 2.0 V). Common mode transient immunity in a
Logic Low level is the maximum tolerable (negative) dV
CM
/dt on the trailing edge of the common mode pulse signal, V
CM
, to assure that the
output will remain in a Logic Low state (i.e., V
O
< 0.8 V).
8. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
9. See Option 020 data sheet for more information.
10. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended.
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage
detection current limit, I
I-O
≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
12. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage
detection current limit, I
I-O
≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
13. This rating is equally validated by an equivalent ac proof test.
Package Characteristics
Over recommended temperature (T
A
= 0°C to 70°C) unless otherwise specied.
Parameter Sym. Device Min. Typ.* Max. Units Test Conditions Fig. Note
Input-Output V
ISO
8-Pin DIP 3750 V rms RH < 50%, 6, 11
Momentary SO-8 t = 1 min.,
Withstand
Widebody 5000 T
A
= 25°C 6, 12
Voltage**
8-Pin DIP 5000 6, 9,
(Option 020) 12
I
I-O
8-Pin DIP 1 µA 45% RH, t = 5 s, 6, 13
V
I-O
= 3 kVdc,
T
A
= 25°C
Input-Output R
I-O
8-Pin DIP 10
12
Ω V
I-O
= 500 Vdc 6
Resistance SO-8
Widebody 10
12
10
13
T
A
= 25°C
10
11
T
A
= 100°C
Input-Output C
I-O
8-Pin DIP 0.6 pF f = 1 MHz 6
Capacitance SO-8
Widebody 0.5 0.6
*All typicals at T
A
= 25°C.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table (if applicable), your
equipment level safety specication or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication num-
ber 5963-2203E.
