OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

74CBTLV16292PAG8

P1-P3P4-P5
1
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV16292
LOW-VOLTAGE 12-BIT 1:2 MUX / DEMUX BUS SWITCH
JUNE 2006
2006 Integrated Device Technology, Inc. DSC-5892/8c
INDUSTRIAL TEMPERATURE RANGE
APPLICATIONS:
• 3.3V High Speed Bus Switching and Bus Isolation
• Resource sharing
FEATURES:
•5
ΩΩ
ΩΩ
Ω A/B bi-directional switch
• Isolation Under Power-Off Conditions
• Make-before-break feature
• Over-voltage tolerant
• Internal 500
ΩΩ
ΩΩ
Ω pull-down resistor to GND
• Latch-up performance exceeds 100mA
•VCC = 2.3V - 3.6V, normal range
• ESD >2000V per MIL-STD-883, Method 3015; >200V using
machine model (C = 200pF, R = 0)
• Available in TSSOP package
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
2
27
1A
12A
SW
SW
SW
S
1
SW
1B1
54
1B2
53
12B1
30
12B2
30
RPULLDOWN
RPULLDOWN
RPULLDOWN
RPULLDOWN
IDT74CBTLV16292
FUNCTIONAL BLOCK DIAGRAM
AB
SELECT CONTROL
CIRCUITRY
SIMPLIFIED SCHEMATIC, EACH
SWITCH
LOW-VOLTAGE 12-BIT 1:2
MUX / DEMUX BUS SWITCH
WITH INTERNAL PULL DOWN
RESISTORS
DESCRIPTION:
The CBTLV16292 is a single 12-bit multiplexing / demultiplexing bus
switch, which provides high speed switching. This device has very low ON
resistance, resulting in under 250ps propagation delay throught the switch.
The demultiplexer side has a 500Ω resistor (R pulldown) termination to
GND to eliminate floating nodes.
When the select (S) input is low, the A port is connected to the B1 port,
and the R pulldown is connected to the B2 port. Similarly, when the S input
is high, A port is connected to B2 port and the R pulldown is connected to
B1 port.
2
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV16292
LOW-VOLTAGE 12-BIT 1:2 MUX / DEMUX BUS SWITCH
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol Description Max. Unit
VCC Supply Voltage Range –0.5 to 4.6 V
VI Input Voltage Range –0.5 to 4.6 V
Continuous Channel Current 128 mA
IIK Input Clamp Current, VI/O < 0 –50 mA
T
STG Storage Temperature Range –65 to +150 °C
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
PIN CONFIGURATION
OPERATING CHARACTERISTICS
(1)
Symbol Parameter Test Conditions Min. Max. Unit
VCC Supply Voltage 2.3 3.6 V
VIH High-Level Control Input Voltage VCC = 2.3V to 2.7V 1.7 — V
VCC = 2.7V to 3.6V 2 —
VIL Low-Level Control Input Voltage VCC = 2.3V to 2.7V — 0.7 V
VCC = 2.7V to 3.6V — 0.8
TA Operating Free-Air Temperature –40 +85 ° C
NOTE:
1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation.
TSSOP
TOP VIEW
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
NC
NC
1B1
1B2
2B1
2B2
3B1
GND
3B2
4B1
4B2
5B1
5B2
6B1
6B2
7B1
7B2
8B1
GND
8B2
9B1
9B2
10B1
10B2
11B1
11B2
12B1
12B2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
S
1A1
NC
2A1
NC
3A1
NC
GND
4A1
NC
5A1
NC
6A1
NC
7A1
NC
V
CC
8A1
GND
NC
9A1
NC
10A1
NC
11A1
NC
12A1
NC
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Input
S Operation
L A Port = B1 Port
RPULLDOWN = B2 Port
H A Port = B2 Port
RPULLDOWN = B1 Port
FUNCTION TABLE
(1)
Pin Names Description
S Select Input
x Ax Port A Inputs or Outputs
x Bx Port B Inputs or Outputs
PIN DESCRIPTION
3
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV16292
LOW-VOLTAGE 12-BIT 1:2 MUX / DEMUX BUS SWITCH
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Operating Condition: TA = –40°C to +85°C
NOTES:
1. Typical values are at 3.3V, +25°C ambient.
2. The increase in supply current is attributable to each input that is at the specified voltage level rather than VCC or GND.
3. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch.
Symbol Parameter Test Conditions Min. Typ.
(1)
Max. Unit
VIK Control Inputs, Data I/O VCC = 3V, II = –18mA — — –1.2 V
II Control Inputs VCC = 3.6V, VI = VCC or GND — — ±1 µA
IOFF VCC = 0V, VI or VO = 0V or 3.6V — — 10 µA
ICC VCC = 3.6V, IO = 0, VI = VCC or GND — — 10 µA
ΔICC
(2)
Control Inputs VCC = 3.6V, one input at 3V, other inputs at VCC or GND — — 300 µ A
CI Control Inputs VI = 3.3V or 0 — 3.5 — pF
CIO(OFF) A port or B port VO = 3.3V or 0 — 22.5 — pF
Max. at V
CC = 2.3V VI = 0 IO = 64mA — 5 8
Typ. at V
CC = 2.5V IO = 24mA — 5 8
RON
(3)
VI = 1.7V IO = 15mA — 11 40 Ω
VI = 0 IO = 64mA — 3 7
VCC = 3V IO = 24mA — 3 7
VI = 2.4V IO = 15mA — 7 15
VCC = 2.5V ± 0.2V VCC = 3.3V ± 0.3V
Symbol Parameter Min. Max. Min. Max. Unit
tPD
(1)
Propagation Delay — 0.15 — 0.25 ns
A to B or B to A
tPD
(2)
Propagation Delay 2.5 7.1 2.5 6.7 ns
S to A
tEN Output Enable Time 1 5.6 1 5 ns
S to B
tDIS Output Disable Time 1 5 1 4.5 ns
S to B
tMB/B
(3,4)
Make-Before-Break Time 0 2 0 2 ns
NOTES:
1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance when driven by an ideal voltage
source (zero output impedance).
2. The condition to measure this propagation delay is by observing the change of voltage on the A port introduced by static fields equal to 3V or 0V for 3.3V±0.3V or VCC or 0 for
2.5V±0.2V on B1 and B2 ports to get the required transition.
3. The make-before-break time is the duration between the make and break, during transition from one selected port to another.
4. This parameter is guaranteed by design but not production tested.
SWITCHING CHARACTERISTICS
P1-P3P4-P5

74CBTLV16292PAG8

Mfr. #:
Buy 74CBTLV16292PAG8
Manufacturer:
IDT
Description:
Digital Bus Switch ICs 12BIT 1:2 MUX 3.3V
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet