Document Number: 38-07296 Rev. *H Page 4 of 12
Maximum Ratings
Supply voltage to ground potential ...............–0.5 V to +7.0 V
DC input voltage (Except REF) ..........–0.5 V to V
DD
+ 0.5 V
DC input voltage REF 0.5 V to 7 V
Storage temperature ................................–65
C to +150 C
Maximum soldering temperature (10 seconds) ......... 260
C
Junction temperature................................................. 150
C
Static discharge voltage
(per MIL-STD-883, Method 3015) ..........................> 2,000 V
Operating Conditions for CY23S05SXX-XX and CY23S09SXX-XX Industrial, Commercial Devices
[5]
Parameter Description Min Max Unit
V
DD
Supply voltage 3.0 3.6 V
T
A
Operating temperature - Ambient (Commercial) 0 70 C
Operating temperature - Ambient (Industrial) -40 85 C
C
L
Load capacitance, below 100 MHz 30 pF
C
L
Load capacitance, from 100 MHz to 133 MHz 10 pF
C
IN
Input capacitance 7 pF
Electrical Characteristics for CY23S05SXC-XX and CY23S09SXC-XX Commercial Temperature Devices
Parameter Description Test Conditions Min Max Unit
V
IL
Input LOW voltage
[6]
0.8 V
V
IH
Input HIGH voltage
[6]
2.0 V
I
IL
Input LOW current V
IN
= 0 V 50.0 A
I
IH
Input HIGH current V
IN
= V
DD
100.0 A
V
OL
Output LOW voltage
[7]
I
OL
= 8 mA (–1)
I
OH =
12
mA (–1H)
0.4 V
V
OH
Output HIGH voltage
[7]
I
OH
= –8 mA (–1)
I
OL
= –12 mA (–1H)
2.4 V
I
DD
(PD mode) Power-down supply current REF = 0 MHz 12.0 A
I
DD
Supply current Unloaded outputs at 66.67 MHz, SEL
inputs at V
DD
32.0 mA
Switching Characteristics for CY23S05SXC-1 and CY23S09SXC-1 Commercial Temperature Devices
[8]
Parameter Description Test Conditions Min Typ Max Unit
t1 Output frequency 30 pF load
10 pF load
10
10
100
133.33
MHz
MHz
Duty cycle
[7]
= t
2
t
1
Measured at 1.4 V, F
out
= 66.67 MHz 40.0 50.0 60.0 %
t3 Rise time
[7]
Measured between 0.8 V and 2.0 V 2.50 ns
t
4
Fall time
[7]
Measured between 0.8 V and 2.0 V 2.50 ns
t
5
Output-to-output skew
[7]
All outputs equally loaded 250 ps
t
6
Delay, REF Rising Edge to
CLKOUT Rising Edge
[7]
Measured at V
DD
/2 0 ±350 ps
t
7
Device-to-device skew
[7]
Measured at V
DD
/2 on the CLKOUT pins 0 700 ps
t
J
Cycle-to-cycle jitter
[7]
Measured at 66.67 MHz, loaded outputs 200 ps
t
LOCK
PLL lock time
[7]
Stable power supply, valid clock presented on
REF pin
1.0 ms
Notes
5. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power up. Power supply sequencing is NOT required.
6. REF input has a threshold voltage of V
DD
/2.
7. Parameter is guaranteed by design and characterization. Not 100% tested in production.
8. All parameters specified with loaded outputs.
