OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TBF-2012-245-R1

P1-P3P4-P6P7-P7
Preliminary
7. Reliability Test
7.1 Electrical
ITEM Specification and Requirement Test Method
Temperature Characteristics Satisfy electrical characteristics Solder the sample on PCB.
Exposure at each temperature,
-40℃, -20℃, 0℃, +25℃, +50℃,
+85℃ for 30minutes
7.2 Mechanical
ITEM Specification and Requirement Test Method
Solderability The Surface of terminal immersed shall
b
e minimum of 95% covered with a new
coating of solder
Solder bath :
After immersing in flux, dip in245
+ 5 ℃ molten solder bath for 2 +
0.5 seconds
Resistance to solder Heat Satisfy electrical characteristics without
distinct deformation in appearance
A. Pre-heat : 100 ~ 110 ℃ for 30
seconds
B. Immersed at solder bath of 270
+ 5℃ for 20 + 1 seconds
Vibration Satisfy electrical characteristics without
Mechanical damage such as break
Vibrate as apply 20 to 2,000Hz,
186m/s
2
(19G) acceleration 1.5mm
amplitude for 2 hours in each o
f
three (X, Y, Z) axis (total 6 hours).
Shock Satisfy electrical characteristics without
mechanical damaged such as break
(1) Break value : 490 N
(2) Duration of pulse : 11ms
(3) 3 times in each positive and
negative direction of 3 mutual
perpendicular directions.
Bending Test Satisfy electrical characteristics without
mechanical damage such as break
Bending value : 3mm for 30 + 1
seconds
Solvent Resistant Marking should be legible without
mechanical and distinct damage in
appearance
(1) Solvent : Trichloroethane or
Isopropyl alcohol.
(2) Immersed in solvent at room
temperature for 90 seconds
Drop Test Satisfy electrical characteristics without
mechanical damage
Drop the sample from a height o
f
1m to concrete ground for 10 times
PAGE 4 OF 4
TITLE : The Engineering Spec. for TBF-2012-245-R1 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
A1
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X = ±
X.X = ±
X.XX = ±
ANGLES ± HOLE DIA. ±
SCALE ﹕ X UNIT ﹕ X
APPROVED BY ﹕Wang-Kevin
RELEASED BY ﹕Steven-Tseng
DESIGNED BY ﹕Steven-Tseng
CHECKED BY ﹕Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
乾坤科技股份有限公司
CYNTEC CO., LTD.
Preliminary
7.3 Load Life
ITEM Specification and Requirement Test Method
Rapid change of temperature Satisfy Electrical Characteristics.
Without distinct damage.
Perform 5 cycles as follows :
−55℃ for 30minutes → room
temperature for 3 minutes→
+125℃ for 30minutes → room
temperature for 3 minutes.
(Dwell time : 5 to 8 minutes)
Humidity Resistance Test Satisfy Electrical Characteristics.
Without distinct damage.
Precondition at +25℃ for 1hour.
Let stand at temperature +40 ± 3
℃, 90~95% relative humidity for
1,000 hours before taking final
measurements.
Low Temperature Store Satisfy Electrical Characteristics.
Without distinct damage.
Solder the sample on PCB.
Exposure at −55 ± 3℃ for 1,000
hours.
1~2 hours exposure at room
temperature and humidity, prior to
measurement.
High Temperature Store Satisfy Electrical Characteristics.
Without distinct damage.
Solder the sample on PCB.
Exposure at +85 ± 3℃ for 1,000
hours.
1~2 hours exposure at room
temperature and humidity, prior to
measurement.
Load Life Satisfy Electrical Characteristics.
Without distinct damage.
Apply 16 Volt voltage at 70±2℃
ambient
PAGE 5 OF 5
TITLE : The Engineering Spec. for TBF-2012-245-R1 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
A1
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X = ±
X.X = ±
X.XX = ±
ANGLES ± HOLE DIA. ±
SCALE ﹕ X UNIT ﹕ X
APPROVED BY ﹕Wang-Kevin
RELEASED BY ﹕Steven-Tseng
DESIGNED BY ﹕Steven-Tseng
CHECKED BY ﹕Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
乾坤科技股份有限公司
CYNTEC CO., LTD.
Preliminary
8. Packaging
8-1 Material : Paper Carrier Tape
8-2 Dimensions
8-2-1 Tape packaging dimensions
Direction mark
Carries cavity
A
0.65 ± 0.10
B
A = 2.28 ± 0.10
B = 2.74 ± 0.10
P(PITCH) = 4.00 ± 0.10
1.5
P
1.75 ± 0.10
8.00 ± 0.30
P
Unit : mm
Sprocket hole
0.60 ± 0.10 2.00 ± 0.10
3.50 ± 0.10
0.1
8-2-2 Setting Direction
8-2-3 Reel dimensions
Unit : mm
10.0 ± 1.5
0.8 ± 0.2
2.0 ± 0.5
21 ± 0.8
13.0 ± 0.5
60 ± 5.0
178 ± 2
PAGE 6 OF 6
TITLE : The Engineering Spec. for TBF-2012-245-R1 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
A1
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X = ±
X.X = ±
X.XX = ±
ANGLES ± HOLE DIA. ±
SCALE ﹕ X UNIT ﹕ X
APPROVED BY ﹕Wang-Kevin
RELEASED BY ﹕Steven-Tseng
DESIGNED BY ﹕Steven-Tseng
CHECKED BY ﹕Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
乾坤科技股份有限公司
CYNTEC CO., LTD.
P1-P3P4-P6P7-P7

TBF-2012-245-R1

Mfr. #:
Buy TBF-2012-245-R1
Manufacturer:
Susumu
Description:
FILTER THIN FILM 2.45GHZ SMD
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet