SPECIFICATION
File Name:IDPC-25-SPEC 2018-01-10
MODEL
OUTPUT
SETUP TIME
Note.4
FREQUENCY RANGE
POWER FACTOR
(Typ.)
EFFICIENCY (Typ.)
AC CURRENT
INPUT
INRUSH CURRENT
(Typ.)
LEAKAGE CURRENT
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
SHORT CIRCUIT
<0.75mA / 277VAC
20 ~ 90% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
418.9Khrs min. MIL-HDBK-217F (25 )℃
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.℃
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time.
5. Aux. 12V will be damaged with short circuit; It will not be available when output voltage is not in constant current region or output no load condition.
6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be
affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
0.12Kg; 72pcs / 9.64Kg / 1.13CUFT
ENVIRONMENT
SAFETY &
EMC
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
SAFETY STANDARDS
Compliance to EN55015, EN61000-3-2 Class C ( ) ; EN61000-3-3,GB17743,GB17625.1,EAC TP TC 020@load 70%≧
EMC IMMUNITY
EMC EMISSION
114.5*72.5*20mm(L*W*H)
Hiccup mode, recovers automatically after fault condition is removed
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( ),EAC TP TC 020surge immunity:Line-Line:1KV
TOTAL HARMONIC DISTORTION
VOLTAGE RANGE Note.3
IDPC-25 -350
IDPC-25 -700
350mA
700mA
500ms / 230VAC 1200ms/115VAC
47 ~ 63Hz
PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
COLD START 30A(twidth= s measured at 50% Ipeak) at 230VAC100μ;Per NEMA 410
IDPC-25 -500
500mA
IDPC-25 -1050
1050mA
RATED CURRENT
RATED POWER
CURRENT TOLERANCE
CONSTANT CURRENT REGION
Note.2
OPEN CIRCUIT VOLTAGE
(max.)
CURRENT RIPPLE
±7.0%
5.0% max. @rated current
THD< 20%(@load 70%/115VAC,230VAC; @load 75%/277VAC)≧≧
(Please refer to “TOTAL HARMONIC DISTORTION” section)
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
(Please refer to "STATIC CHARACTERISTIC" section)
90 ~ 295VAC 127 ~ 417VDC
AUXILIARY DC OUTPUT
Note.5
Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only
25W Constant Current Mode LED Driver
IDPC-25 series
<0.5W for Blank-Type, <1.2W for A-Type
NO LOAD POWER CONSUMPTION
24.5W
25.2W
100V
49 ~ 70V
25.2 ~ 36V
63V
25W
35 ~ 50V
75V
25.2W
16.8 ~ 24V
36V
82%
81.5%
81.5%
80%
0.4A/115VAC 0.16A/230VAC 0.13A/277VAC
WORKING TEMP.
Ta=-20 ~ +50 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃
GB19510.1,GB19510.14, EAC TP TC 004 approved
UL8750,CSA C22.2 NO.250.13-12;ENEC EN61347-1 & EN61347-2-13 independent, EN62384,
