84134080 Datasheet 84134080, 84137030, 2982595 | P1-P3

102895_04_en

INTERFACE

PLC-…-EIK 1-SVN 24P/P

PLC-…-EIK 1-SVN 24M

Data Sheet

Description

The PLC-…-EIK 1-SVN 24… electronic sensor terminal

block converts the variable resistance of a NAMUR sensor

into a digital signal that can be read by a PLC.

In addition, the internal circuitry monitors the sensor side for

a short circuit or wire break and indicates these errors via

the integrated LED.

Thanks to a corresponding resistance circuit, the

PLC-…-EIK 1-SVN 24… can be used to monitor all me-

chanical switches (N/C or N/O contacts) for short circuits

and/or wire breaks.

In addition to a high packing density, this switching amplifier

features the following:

– Stabilized supply voltage for the NAMUR proximity

switch

– Defined recognition and evaluation of the analog sen-

sor signal

– Monitoring of the sensor cable for short circuits and

wire breaks; a fault is indicated by the red LED

– Status display (high signal) via green LED

– 24 V/50 mA digital output for directly connecting pro-

grammable logic controllers

– Positive or negative error output depending on the

version

– Additional output for error messages

– Connection option for PLC V8 adapter

– Bridging and labeling with standard terminal block

accessories

Make sure you always use the latest documentation.

It can be downloaded at www.download.phoenixcontact.com

A conversion table is available on the Internet at

www.download.phoenixcontact.com/general/7000_en_00.pdf

This data sheet is valid for all products listed on the following page:

PLC Electronic Sensor Terminal Blocks

for NAMUR Proximity Sensors

PLC-…-EIK 1-SVN 24…

102895_04_en PHOENIX CONTACT 2

Ordering Data

Technical Data

PLC Electronic Sensor Terminal Block for NAMUR Proximity Sensors

Description Type Order No. Pcs./Pck.

PLC electronic sensor terminal block for NAMUR proximity sensors

Positive switching, with screw connection PLC-SC-EIK 1-SVN 24P/P 2982663 10

Positive switching, with spring-cage connection PLC-SP-EIK 1-SVN 24P/P 2982676 10

Negative switching, with screw connection PLC-SC-EIK 1-SVN 24M 2982595 10

Negative switching, with spring-cage connection PLC-SP-EIK 1-SVN 24M 2982605 10

Accessories

Description Type Order No. Pcs./Pck.

Double-level terminal block, with pre-assembled resistors UKK 5-2R/NAMUR 2941662 50

Insulating plate PLC-ATP BK 2966841 25

For other accessories such as power terminal blocks and plug-in bridges please consult the INTERFACE catalog and www.phoenixcontact.com.

Power Supply

Nominal input supply voltage U

24 V DC ±20%

Typical input current at U

14 mA, approximately

Transmission frequency f

limit

350 Hz, approximately

Input circuit Green LED, protection against polarity reversal, surge protection

The PLC-ATP BK insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages

greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (FBST 8-PLC... or FBST 500... can be used for

potential bridging) and for safe isolation between adjacent modules.

Control Circuit

Non-load voltage 8.2 V DC ±10%

Switching point according to EN 60947-5-6

In conductive state

In disabling state

In the event of short circuit

In the event of wire break

≥ 2.1 mA

≤ 1.2 mA

20 mA, approximately

12 mA, approximately

Switching hysteresis 0.2 mA, approximately

Internal resistance 1 kΩ, approximately

Protective circuit Surge protection

Alarm Output

Operating voltage range (negative switching) 3 V DC ... 33 V DC

Operating voltage range (positive switching) U

- 1.5 V

Limiting continuous current 100 mA

Voltage drop at maximum limiting continuous current ≤ 1.5 V

Output circuit Red LED, surge protection

Signal Output

Limiting continuous current 50 mA

Voltage drop U

at maximum limiting continuous current ≤ 1.5 V

Output voltage (positive switching)

In conductive state

In disabling state

≤ 100 mV

- U

Output voltage range (negative switching) 3 V DC ... 33 V DC

Output circuit Surge protection

PLC-…-EIK 1-SVN 24…

102895_04_en 3

PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany

Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3-4 12 00

www.phoenixcontact.com

Block Diagrams

Positive Switching Error Output ERR

Figure 1 Block diagram for terminal blocks with positive

switching outputs (P/P): Both +24 V connec-

tion terminal blocks are bridged internally

Negative Switching Error Output ERR

Figure 2 Block diagram for terminal blocks with nega-

tive switching (M) outputs: Both GND connec-

tion terminal blocks are bridged internally

Truth Table

Application Examples

Figure 3 Application with NAMUR sensor

Figure 4 Application with limit switch

General Data

Rated insulation voltage 50 V DC

Impulse voltage withstand level/insulation 0.4 kV/basic insulation

Ambient operating temperature range -20°C ... 50°C

Nominal operating mode 100% operating factor

Inflammability class according to UL 94 (housing) V0

Air and creepage distances between circuits According to DIN EN 50178

Pollution degree 2

Surge voltage category I

Mounting position Any

Assembly Can be aligned without spacing

Dimensions (W x H x D) 6.2 mm x 86 mm x 80 mm

Conductor cross section

With screw connection

With spring-cage connection

0.14 mm

... 2.5 mm

0.2 mm

... 2.5 mm

Housing material Polybutylene terephthalate PBT non-reinforced, green

GND

OUT

ERR

GND

OUT

ERR

Sensor status Switching level LED

OUT ERR green red

Conductive L L off off

Disabling H L ON off

Short circuit L H off ON

Wire break L H off ON

NAMUR-Initiator

ERR

OUT

GND

NAMUR sensor

Limit switch

UKK 5-2R/NAMUR

10k

ERR

OUT

GND

P1-P3

84134080

Mfr. #:

Buy 84134080

Manufacturer:

Crydom

Description:

Solid State Relays - Industrial Mount SOLID STATE RELAY 24-280 VAC

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

84134080

84134080

Products related to this Datasheet