HK (AHK)
2) DC coils (at 20°C 68°F)
Notes: 1. The rated excitation current is ±10% (20°C 68°F).
2. The coil resistance for DC operation is the value measured when the coil temperature is 20°C 68°F. Compensate ±0.4% for every ±1°C change in temperature.
3. The relay operates in a range of 80% to 110 % V of the nominal coil voltage, but ideally, in consideration of temporary voltage fluctuations, it should be operated at
the nominal coil voltage.
4. For use with 200 V DC, connect a 10 KΩ (5W) resistor, in series, to the 100 V DC relay.
5. The maximum applied voltage is the maximum voltage fluctuation value for the coil power supply. This value is not a permissible value for continuous operation.
(This value differs depending on the ambient temperature. Please contact us for details.)
2. Specifications
Notes: If integrating into electrical appliances that will be subject to compliance to the Electrical Appliance and Material Safety Law, please use in an ambient temperature
between –50°C to +40°C –58°F to +104°F (AC type).
*1. This value can change due to the switching frequency, environmental conditions and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. For the AC coil types, the operate/release time will differ depending on the phase.
*3. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage
conditions in NOTES.
Nominal coil voltage
Nominal coil current,
mA
Nominal operating
power, W
Coil resistance,
Ω
Pick-up voltage
(at 20°C 68°F)
Drop-out voltage
(at 20°C 68°F)
Max. applied voltage
(at 70°C 158°F)
6V DC 150
0.9
40
80%V or less of
nominal voltage
(Initial)
10%V or more of
nominal voltage
(Initial)
110%V of
nominal voltage
12V DC 75 160
24V DC 37 650
48V DC 18.5 2,600
100/110V DC 10 1.0 10,000
Characteristics Item Specifications
Contact
Contact resistance (Initial) Max. 50 mΩ (By voltage drop 6 V DC 1A)
Contact material AgSnO
2 type
Rating
Nominal switching capacity 1 Form C: 15A 125V AC (resistive load), 2 Form C: 10A 125V AC (resistive load)
Max. switching voltage 250V AC, 125V DC
Max. switching current 15A (1 Form C), 10A (2 Form C)
Min. switching capacity (Reference value)*
1
100mA 5V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 100MΩ (at 500V DC) Measurement at same location as “Breakdown voltage” section.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrms for 1min. (Detection current: 10mA.)
Between contact sets 2,000 Vrms for 1min. (Detection current: 10mA.)
Between contact and coil 2,000 Vrms for 1min. (Detection current: 10mA.)
Temperature rise (coil) Max. 80°C 176°F (By resistive method, nominal voltage)
Operate time (at 20°C 68°F)*
2
Max. 25ms (Nominal coil voltage applied to the coil, excluding contact bounce time.)
Release time (at 20°C 68°F)*
2
Max. 25ms (Nominal coil voltage applied to the coil, excluding contact bounce time.)
(without diode)
Mechanical
characteristics
Shock resistance
Functional Min. 196 m/s
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)
Destructive Min. 980 m/s
2
(Half-wave pulse of sine wave: 6 ms.)
Vibration resistance
Functional 10 to 55 Hz at double amplitude of 1 mm (Detection time: 10µs.)
Destructive 10 to 55 Hz at double amplitude of 2 mm
Expected life
Mechanical AC type: 5×10
7
(at 180 times/min.), DC type: 10
8
(at 180 times/min.)
Electrical AC load
1 Form C: 15A 125V AC (resistive load) (cosϕ=1), Min. 2×10
5
2 Form C: 10A 125V AC (resistive load) (cosϕ=1), Min. 5×10
5
Conditions
Conditions for operation, transport and storage*
3
Ambient temperature:
–50°C to +70°C –58°F to +158°F (Without LED indication);
–50°C to +60°C –58°F to +140°F (With LED indication)
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
Max. Operating speed 20 times/min. (at max. rating)
Unit weight Approx. 35g 1.23 oz
ASCTB113E 201209-T
Panasonic Corporation Automation Controls Business Unit industrial.panasonic.com/ac/e
