EK-Z7-ZC702-G Datasheet EK-Z7-ZC702-G, EK-Z7-ZC702-G-J | P1-P3

Zynq-7000 All Programmable SoC ZC702

Evaluation Kit

Quick Start Guide

The Zynq®-7000 All Programmable (AP) SoC ZC702 Evaluation Kit provides a platform for evaluating Xilinx

Zynq-7000 AP SoC devices. The ZC702 kit contains the necessary hardware, tools, and IP to quickly evaluate and

start the development of your embedded system.

This guide provides a kit overview and step-by-step instructions to set up and configure the board, run the built-in

self-test (BIST), install Xilinx tools, and redeem the license voucher.

ZC702 Evaluation Kit

For more information, visit www.xilinx.com/zc702.

X-Ref Target - Figure 1-1

(WKHUQHW

&URVVRYHU

&DEOH

3RZHU

6XSSO\

=&

%DVH%RDUG

86%

+XE

86%7\SH$WR

0LQL%$GDSWRU

6'&DUGZLWK

5HIHUHQFH'HVLJQ

86%&DEOHV

7\SH$WR0LQL%

DQG7\SH$WR

0LFUR%

+'0,

&DEOH

;LOLQ[9LYDGR

'HVLJQ6XLWH

,QVWDOODWLRQ'9'

Built-In Self-Test (BIST) Instructions

ZC702 Evaluation Kit

STEP 1: Install Driver and Terminal Emulator

Install the Silicon Labs CP210x USB-to-UART drivers

and a terminal emulator for the USB-to-UART on your

PC.

Install the CP210x USB to UART drivers as described in

www.xilinx.com/kits/cp210x

Xilinx recommends using Tera Term for terminal

emulation as described in www.xilinx.com/kits/

teraterm.

Note: If switches, jumpers, or flash memory images

have been changed, refer to www.xilinx.com/kits/

zc702default.

X-Ref Target - Figure 1-2

STEP 2: Set Switches

Set DIP switch SW16 to this configuration (00010):

STEP 3: Connect Computer to ZC702 Board

Connect your computer to J17 on the ZC702 board

using the Type-A to Mini-B USB cable.

X-Ref Targ et - Figure 1-3

STEP 4: Connect Power

Connect the 6-pin power supply plug to J60 and turn

the board on with SW11.

STEP 5: Set Up Terminal Emulator: Select COM Port

Open Tera Term, select Serial, and choose the COM

port that correlates with the Silicon Labs CP210x

USB-to-UART bridge. Click OK. Note the assigned COM

port for Step 7.

X-Ref Target - Figure 1-4

STEP 6: Set Up Terminal Emulator: Select Serial Port

Go to Setup and click Serial port to configure the

terminal serial port setting.

STEP 7: Set Up Terminal Emulator: Serial Setup

Select the same COM port assigned in Step 5 and set

the Baud rate to 115200, the Data to 8 bit, the Parity

to none, Stop to 1 bit, and Flow control to none. Click

OK to save the settings.

X-Ref Targ et - Figure 1-5

STEP 8: Initialize Configuration

Press SW1 (POR_B) to reinitialize the configuration for

the ZC702 board.

STEP 9: Terminal Display

After the ZC702 board is configured

in Step 8, text appears in the

terminal emulator window. Type the

number or letter associated with a

listed option to run a test

application. For example, type 2 to

run the LED Test application.

Note: DIP switches SW15-1 and

SW15-2 are tied in parallel to

pushbuttons SW13 and SW14,

respectively. For SWITCH Test 5,

either use DIP switches SW15-1

and SW15-2, or keep SW15-1 and

SW15-2 OFF and use pushbuttons

13 and 14.

OFF

P1-P3 P4-P4

EK-Z7-ZC702-G

Mfr. #:

Buy EK-Z7-ZC702-G

Manufacturer:

Xilinx

Description:

Field-Programmable Gate Array

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

EK-Z7-ZC702-G

EK-Z7-ZC702-G

Products related to this Datasheet