HEDR-55L2-BHL9

4
Absolute Maximum Rating
Parameter Value Units Notes
Storage Temperature, T
S
-40 to 100
-20 to 85
°C
High temperature option
Low temperature option
Operating Temperature, T
A
-40 to 100
-20 to 85
°C
High temperature option
Low temperature option
Supply Voltage, V
CC
-0.5 to 7 V
Output Current per Channel, I
OUT
Voltage
Line Driver
5
20
mA
mA
Vibration 10G, 55 to 1000 Hz
Shaft Axial Play ±0.175 mm
Shaft TIR (max.) 0.05 mm
Output waveform
Direction of Rotation: When the encoder rotates in the counter-clockwise direction (as viewed from the top of the
encoder), channel A will lead channel B. If it rotates in the clockwise direction, channel B will lead channel A.
Index Pulse Width (P
O
): The number of electrical degrees that an index output is high during one full shaft rotation. This
value is nominally 90°e (1/4 cycle) gated to signals A and B, both at low state.
Encoder
Motor
shaft
C
360 e Deg
A
S1 S2 S3 S4
B
Po
I
Gated Index of 90°e
Codewheel rotation movement (Anti-clockwise)
P
Amplitude
Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Units Notes
Temperature T
A
-40
-20
100
85
°C High temperature option
Low temperature option
Supply Voltage V
CC
4.5 5.0 5.5 V Ripple < 100 mV
p-p
Current Consumption 38 mA No load
Count Frequency
[1]
f 320
[2]
kHz Velocity (rpm) x N/60
Notes:
1. Applicable for line driver output.
2. Valid for 2400 CPR and above.
5
Encoding Characteristics
Encoding characteristics over recommended operating range and recommended mounting tolerances, unless otherwise specied.
Part No. Description Symbol Typ. Max. Notes
HEDR-5xxx
(Three Channel)
Pulse Width
Logic State Width
Index Pulse Width
P
S
P
o
90°
P ± P/4
S ± S/2
Voltage Output
Rise time
Fall time
t
r
t
f
1 µs
Line Driver
Rise time
Fall time
t
r
t
f
200 ns
Mechanical Characteristics
Parameter Symbol Dimension Tolerance Units
Blind Hollow Shaft diameter Refer to ordering information g6 mm
Shaft Length 11.5 to 14.5
*
mm
Height 20 ± 0.5 mm
Width 30 ± 0.5 mm
Length 35 ± 0.5 mm
Hub Set Screw M3
* - Not applicable for 2048 cpr option. For 2048 cpr option, the recommend range is 11.5 to 13.5 mm.
Ribbon cable
Line Driver option
Pin No. Pin Assignment
1 NC
2 VCC
3 GND
4 NC
5 A −
6 A +
7 B −
8 B +
9 I −
10 I +
Single-ended option
Pin No. Pin Assignment
1 NC
2 VCC
3 GND
4 NC
5 NC
6 A +
7 NC
8 B +
9 NC
10 I +
500 ± 13 mm
RED LINE CABLE (pin 1)
20
15
17.5
30
16.3
12.8
6
2.54
PITCH = 2.54
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2014 Avago Technologies. All rights reserved.
AV02-3823EN - October 30, 2014
Ordering Information
Available options for HEDR-5xxx-xxxx
HEDR-5 x x x
-
xx x x
| | | | | |
Mounting
Type
Output
Type
Output Wire
Cabling Type CPR
Temperature Rating/
Index Gating
Shaft
Diameter
5 – Standard E – Voltage (TTL) 2 – Ribbon B2 – 1200 0 – High /90° 0 – 2 mm
6 – External Ears L – Line Driver B4 – 1250 1 – High / 180⁰ 1 – 3 mm
7 – Standard
Through Hole
B8 – 1500 L – Std / 90⁰ 3 – 5/32”
BB – 1800 M – Std / 180⁰ 4 – 3/16”
8 – External Ears
Through Hole
BH – 2048
Note:
High -40 to 100 °C
Std -20 to 85 °C
5 – 1/4
BL – 2400 6 – 4 mm
BP – 2500 7 – 5 mm
BS – 2880 8 – 6 mm
BV – 3000 9 – 8 mm
BY – 3600
Currently available options
High temperature Standard temperature
1. HEDR-55L2-BH07 11. HEDR-55L2-BHL7
2. HEDR-55L2-BH09 12. HEDR-55L2-BHL9
3. HEDR-55L2-BL07 13. HEDR-55L2-BPL7
4. HEDR-55L2-BL09 14. HEDR-55L2-BPL9
5. HEDR-55L2-BV07 15. HEDR-55L2-BYL8
6. HEDR-55L2-BV09
7. HEDR-55L2-BY07
8. HEDR-55L2-BY09
9. HEDR-55L2-BP07
10. HEDR-55L2-BP09
Note: For other options, please refer to factory.

HEDR-55L2-BHL9

Mfr. #:
Manufacturer:
Broadcom / Avago
Description:
Encoders AOR,STDMT,DIF RIBB,2048,LT,8MM
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union