Ultra-Sensitive Dual-Channel Quadrature
Hall-Effect Bipolar Switch
A3425
10
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Typical Thermal Performance
The device must be operated below the maximum junction
temperature of the device, T
J(max)
. Under certain combinations of
peak conditions, reliable operation may require derating sup-
plied power or improving the heat dissipation properties of the
application. This section presents a procedure for correlating
factors affecting operating T
J
. (Thermal data is also available on
the Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
JA
, is a fi gure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity,
K, of the printed circuit board, including adjacent devices and
traces. Radiation from the die through the device case, R
JC
, is
relatively small component of R
JA
. Ambient air temperature,
T
A
, and air motion are signifi cant external factors, damped by
overmolding.
The effect of varying power levels (Power Dissipation, P
D
), can
be estimated. The following formulas represent the fundamental
relationships used to estimate T
J
, at P
D
.
P
D
= V
IN
×
I
IN
(1)
T = P
D
×
R
JA
(2)
T
J
= T
A
+ ΔT (3)
For example, given common conditions such as: T
A
= 25°C,
V
CC
= 12 V, I
CC
= 4 mA, and R
JA
= 140 °C/W, then:
P
D
= V
CC
×
I
CC
= 12 V
×
4 mA = 48 mW
T = P
D
×
R
JA
= 48 mW
×
140 °C/W = 7°C
T
J
= T
A
+ T = 25°C + 7°C = 32°C
A worst-case estimate, P
D(max)
, represents the maximum allow-
able power level (V
CC(max)
, I
CC(max)
), without exceeding T
J(max)
,
at a selected R
JA
and T
A
.
Example: Reliability for V
CC
at T
A
=
150°C, package L, using
minimum-K PCB
Observe the worst-case ratings for the device, specifi cally:
R
JA
=
140
°C/W, T
J(max)
=
165°C, V
CC(max)
=
18
V, and
I
CC(max)
=
6
mA.
Calculate the maximum allowable power level, P
D(max)
. First,
invert equation 3:
T
max
= T
J(max)
– T
A
= 165
°C
–
150
°C = 15
°C
This provides the allowable increase to T
J
resulting from internal
power dissipation. Then, invert equation 2:
P
D(max)
= T
max
÷ R
JA
= 15°C ÷ 140 °C/W = 107 mW
Finally, invert equation 1 with respect to voltage:
V
CC(est)
= P
D(max)
÷ I
CC(max)
= 107 mW ÷ 6 mA = 18 V
The result indicates that, at T
A
, the application and device can
dissipate adequate amounts of heat at voltages ≤V
CC(est)
.
Compare V
CC(est)
to V
CC(max)
. If V
CC(est)
≤ V
CC(max)
, then reli-
able operation between V
CC(est)
and V
CC(max)
requires enhanced
R
JA
. If V
CC(est)
≥ V
CC(max)
, then operation between V
CC(est)
and
V
CC(max)
is reliable under these conditions.
