EVAL-AD5040SDZ/EVAL-AD5060SDZ to EVAL-AD5062SDZ User Guide UG-923
Rev. 0 | Page 13 of 13
ORDERING INFORMATION
BILL OF MATERIALS
Table 3.
Qty Reference Designator Description Part Number
1
6 C1, C4, C6, C7, C10, C13 100 nF, 50 V, 0603 capacitor FEC 8820023
5 C2, C3, C5, C8, C9 10 µF, 16 V, tantalum capacitor FEC 1432339
1 C11 Multilayer ceramic capacitor Do not insert
1 µF, 16 V, tantalum capacitor
1 G1 Copper short Not applicable
1 J1 120-way connector, 0.6 mm pitch FEC 1324660
2 J2, J3 50 Ω SMA jack, vertical FEC 1814376
2 J4, J5 2-pin terminal block (5 mm pitch) FEC 1177875
1 J6 2-pin terminal block (5 mm pitch) FEC 151789
1 J7 7-pin SIL, 0.1" pitch, header FEC 1022257 (8-way, cut to size)
2 LK1, LK2 Jumper block using 3-pin SIP header FEC 1022248 and 150410
3 R1 to R3 0 Ω, 1%, 0603 resistor FEC 9331662
2 R4, R6 0603 SMD resistor Do not insert
10 R5, R7 to R15 100 kΩ, 1%, 0603 resistor FEC 9330402
2 T1, T2 Red test point FEC 8731144
1 U1
2
DAC AD5060BRJZ-1500RL7/AD5040BRJZ-RL7/
AD5061BRUZ-1REEL7/AD5062-1REEL7
1 U2 4.096 V reference ADR444ARZ
1 U3 64K I
2
C serial EEPROM FEC 9758070
1 U4 Ultralow noise, linear regulator, adjustable ADP7102ACPZ-R7
1 U5 5 V, ultralow noise, linear regulator ADP7102ACPZ-5.0-R7
2 SCREW1, SCREW2 M3X10 nylon screw FEC 7070597
2 NUT1, NUT2 M3 nylon nut/washer FEC 7061857
4 Stick on feet, small, one on each corner FEC 1165061
1
FEC is Farnell Electronics Components.
2
The Part Number populated depends on the evaluation board used.
I
2
C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of
the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the lic
ense granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engi
neer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS
Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreemen
t shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG14140-0-4/16(0)
