MC74LVX4066
http://onsemi.com
3
MAXIMUM RATINGS
Symbol Parameter Value Unit
V
CC
Positive DC Supply Voltage (Referenced to GND) – 0.5 to + 7.0 V
V
IS
Analog Input Voltage (Referenced to GND) – 0.5 to V
CC
+ 0.5 V
V
in
Digital Input Voltage (Referenced to GND) – 0.5 to V
CC
+ 0.5 V
I
in
DC Current Into or Out of ON/OFF Control Pins ± 20 mA
I
s
DC Current Into or Out of Switch Pins ± 20 mA
P
D
Power Dissipation in Still Air, SOIC Package†
TSSOP Package†
500
450
mW
T
stg
Storage Temperature – 65 to + 150
_C
T
L
Lead Temperature, 1 mm from Case for 10 Seconds 260
_C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress
ratings only. Functional operation above the Recommended Operating Conditions is not im-
plied. Extended exposure to stresses above the Recommended Operating Conditions may af-
fect device reliability.
†Derating — SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: − 6.1 mW/_C from 65_ to 125_C
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Max Unit
V
CC
Positive DC Supply Voltage (Referenced to GND) 2.0 6.0 V
V
IS
Analog Input Voltage (Referenced to GND) GND V
CC
V
V
in
Digital Input Voltage (Referenced to GND) GND V
CC
V
V
IO
* Static or Dynamic Voltage Across Switch − 1.2 V
T
A
Operating Temperature, All Package Types – 55 + 85
_C
t
r
, t
f
Input Rise and Fall Time, ON/OFF Control
Inputs (Figure 10) V
CC
= 3.3 V ± 0.3 V
V
CC
= 5.0 V ± 0.5 V
0
0
100
20
ns/V
*For voltage drops across the switch greater than 1.2 V (switch on), excessive V
CC
current may
be drawn; i.e., the current out of the switch may contain both V
CC
and switch input
components. The reliability of the device will be unaffected unless the Maximum Ratings are
exceeded.
DC ELECTRICAL CHARACTERISTIC Digital Section (Voltages Referenced to GND)
Symbol Parameter Test Conditions
V
CC
V
Guaranteed Limit
Unit
– 55 to 25_C v 85_C v 125_C
V
IH
Minimum High−Level Voltage
ON/OFF Control Inputs (Note 1)
R
on
= Per Spec 2.0
3.0
4.5
5.5
1.5
2.1
3.15
3.85
1.5
2.1
3.15
3.85
1.5
2.1
3.15
3.85
V
V
IL
Maximum Low−Level Voltage
ON/OFF Control Inputs (Note 1)
R
on
= Per Spec 2.0
3.0
4.5
5.5
0.5
0.9
1.35
1.65
0.5
0.9
1.35
1.65
0.5
0.9
1.35
1.65
V
I
in
Maximum Input Leakage Current
ON/OFF Control Inputs
V
in
= V
CC
or GND 5.5V ± 0.1 ± 1.0 ± 1.0
mA
I
CC
Maximum Quiescent Supply
Current (per Package)
V
in
= V
CC
or GND V
IO
= 0 V 5.5 4.0 40 160
mA
1. Specifications are for design target only. Not final specification limits.
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V
in
and
V
out
should be constrained to the
range GND v (V
in
or V
out
) v V
CC
.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V
CC
).
Unused outputs must be left open.
I/O pins must be connected to a
properly terminated line or bus.
