EW710B

Hybrid Hall Effect ICs EW-series
●Absolute Maximum Ratings (Ta=25℃
(*)Please refer to Supply Voltage Derating Curve.
●Magnetic and Electrical Characteristics (Ta=25℃
1mT=10Gauss
Item
Conditions Min. Unit
Symbol
3
1
-6
2
12
3
-3
6
5
26.4
6
-1
0.4
1
6
V
mT
mT
mT
V
μA
mA
Typ. Max.
Release Point
Hysteresis
Output Saturation Voltage
Output Leakage Current
Supply Current
V
cc
=12V
V
cc
=12V
V
cc
=12V
V
cc
=12V,OUT''L'',I
sink
=10mA
V
cc
=12V,OUT''H'',V
out
=12V
V
cc
=12V,OUT''H''
V
CC
B
OP
B
rp
B
h
V
sat
I
leak
I
cc
Operating Point
Supply Voltage
Item Limit Unit
Symbol
V
cc
V
o(off)
Isink
Topr
Tstg
26.4
(*)
V
cc
10
40 115
40 125
V
V
mA
Supply Voltage
Output L Current
Output H Voltage
Operating Temperature Range
Storage Temperature Range
Voltage Regulator
Hall Element
Output Stage
Schmitt Trigger
Amplifer
1:Vcc
3:OUT
2:GND
Reg.
Amp.
●Functional Block Diagram
●Operational Characteristics
S
N
Marking
1:Vcc
2:GND
3:OUT
123
Another product type with pulled-up resistor(EW-712B).
Please contact AKM to obtain the detail information.
N-pole S-pole
0
BopBrp
Bh
Vsat
L
Vout
H
Magnetic flux density
EW-710B
Supply Voltage
3∼26.4
Bipolar Hall
Effect Latch
High Sensitivity
Bop3mT
Output
Open Collector
SIP
EW-710B is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.
Shipped in bulk(500pcs/Bag)
Hall Element
Continuous
Excitation
Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue.
69
EW-710B
●Temparature Dependence of Bop. Brp ●Supply Voltage Dependence of Bop. Brp
6
4
2
0
2
4
6
60
40
20 0 20 40 60 80 100 120 140
Bop
Brp
Operating Point[mT]
Ambient Temperature(℃)
V
cc
=12V
6
4
2
0
2
4
6
5101520 30250
Operating Point[mT]
Vcc(V)
T
a
=25
Bop
Brp
•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the
advance written approval of our sales staff.
Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,
adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such
applications is understood to be fully at the risk of the customer using our devices or systems.
●Supply Voltage ●Package(Unit:mm)
30
25
20
15
10
5
0
Supply Voltage[V]
60
40
20 0 20 40 60 80 100 120 140
Ambient Temperature[℃]
10°
10°
45°
4.1
φ0.3
Sensor Center
1.15
0.25
1.27
0.55
3
0.4
0.6
3.0Max. 15.0
1.27
123
3OUT
2GND
1Vcc
Note) The sensor center is located
    within the φ0.3mm circle.
c
e
m
p
q
r
4.5
70
IMPORTANT NOTICE
These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make
inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or
authorized distributors as to current status of the products.
Descriptions of external circuits, application circuits, software and other related
information contained in this document are provided only to illustrate the
operation and application examples of the semiconductor products. You are
fully responsible for the incorporation of these external circuits, application
circuits, software and other related information in the design of your
equipments. AKM assumes no responsibility for any losses incurred by you or
third parties arising from the use of these information herein. AKM assumes no
liability for infringement of any patent, intellectual property, or other rights in
the application or use of such information contained herein.
Any export of these products, or devices or systems containing them, may
require an export license or other official approval under the law and
regulations of the country of export pertaining to customs and tariffs, currency
exchange, or strategic materials.
AKM products are neither intended nor authorized for use as critical
components
Note1)
in any safety, life support, or other hazard related device or
system
Note2)
, and AKM assumes no responsibility for such use, except for the
use approved with the express written consent by Representative Director of
AKM. As used here:
Note1) A critical component is one whose failure to function or perform
may reasonably be expected to result, whether directly or indirectly, in the
loss of the safety or effectiveness of the device or system containing it,
and which must therefore meet very high standards of performance and
reliability.
Note2) A hazard related device or system is one designed or intended for
life support or maintenance of safety or for applications in medicine,
aerospace, nuclear energy, or other fields, in which its failure to function
or perform may reasonably be expected to result in loss of life or in
significant injury or damage to person or property.
It is the responsibility of the buyer or distributor of AKM products, who
distributes, disposes of, or otherwise places the product with a third party, to
notify such third party in advance of the above content and conditions, and
the buyer or distributor agrees to assume any and all responsibility and
liability for and hold AKM harmless from any and all claims arising from the
use of said product in the absence of such notification.
April 4, 2012

EW710B

Mfr. #:
Manufacturer:
Description:
MAGNETIC SWITCH LATCH 3SIP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet