OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EALP03SXARA0-AM

P1-P3P4-P6P7-P9P10-P12
DATASHEET
P-LED
EALP03SXARA0-AM
10
Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.2.2013 Issue No:1
www.everlightamericas.com
Notes
1. Lead Forming
During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy
bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage the
LED’s characteristics or it may break the LEDs.
Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may
cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead
position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration of the
epoxy resin and this will degrade the LEDs.
2. Storage
The LEDs should be stored at 30°C or less and 60%RH or less after being shipped from Everlight
Americas and the storage life limits are 3 months. If the LEDs are stored for 3 months or more,
they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture
absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity environments
where condensation can occur.
3. Soldering
Careful attention should be paid during soldering. Solder the LED no lower than 1.6mm from the
base of stopper is recommended.
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly
when soldering.
Recommended soldering conditions:
Dip and hand soldering should not be done more than one time.
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration
until the LEDs return to room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
Although the recommended soldering conditions are specified in the above table, dip or
Hand Soldering
DIP Soldering
Temp. at tip of iron
300℃ Max. (30W Max.)
Preheat temp.
100℃ Max. (60 sec Max.)
Soldering time
3 sec Max.
Bath temp.
260 Max.
Distance
No lower than 1.6mm from
the base of stopper
Bath time.
5 sec Max.
Distance
No lower than 1.6mm from the
base of stopper
DATASHEET
P-LED
EALP03SXARA0-AM
11
Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.2.2013 Issue No:1
www.everlightamericas.com
handsoldering at the lowest possible temperature is desirable for the LEDs.
Wave soldering parameter must be set and maintain according to recommended temperature and
dwell time in the solder wave.
4. Cleaning
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a
duration of no more than one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of
ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled
condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause damage to the
LED
5. Heat Management
Heat management of LEDs must be taken into consideration during the design stage of LED
application. The current should be de-rated appropriately by referring to the de-rating curve found
in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer
to the data sheet de-rating curve.
6. ESD (Electrostatic Discharge)
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LEDs
plastic lens as a result of friction between LEDs during storage and handing.
7. Other
Above specification may be changed without notice. EVERLIGHT AMERICAS will reserve
authority on material change for above specification.
When using this product, please observe the absolute maximum ratings and the instructions for
using outlined in these specification sheets. EVERLIGHT AMERICAS assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT
AMERICAS corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT AMERICAS’s consent.
DATASHEET
P-LED
EALP03SXARA0-AM
12
Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.2.2013 Issue No:1
www.everlightamericas.com
Revision History
Rev.
Modified date
File modified contents
2
2013/5/2
Change the form of data
P1-P3P4-P6P7-P9P10-P12

EALP03SXARA0-AM

Mfr. #:
Buy EALP03SXARA0-AM
Manufacturer:
Description:
Standard LEDs - Through Hole Superflux (Piranha) Thru-Hole
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet