www.vishay.com
6
Document Number: 69828
S10-1383-Rev. E, 21-Jun-10
Vishay Siliconix
DG4051A, DG4052A, DG4053A
Notes:
a. V
IN
= input voltage to perform proper function.
b. Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
SPECIFICATIONS FOR UNIPOLAR SUPPLIES
Parameter Symbol
Test Conditions
Unless Otherwise Specified
V
CC
= + 3 V, V
EE
= 0 V
V
IN(A, B, C and ENABLE)
= 1.4 V, 0.6 V
a
Temp.
b
Typ.
c
- 40 °C to 125 °C - 40 °C to 85 °C
Unit Min.
d
Max.
d
Min.
d
Max.
d
Analog Switch
Analog Signal Range
e
V
ANALOG
Full 0303V
On-Resistance
R
ON
I
S
= 1 mA, V
D
= 1.5 V
Room
Full
175 265
310
265
298
Switch Off
Leakage Current
I
S(off)
V+ = + 3.3 V, V- = 0 V
V
D
= 0.3 V/3.0 V, V
S
= 3.0 V/0.3 V
Room
Full
± 0.02 - 1
- 50
1
50
- 1
- 5
1
5
nA
I
D(off)
Room
Full
± 0.02 - 1
- 50
1
50
- 1
- 5
1
5
Channel On
Leakage Current
I
D(on)
V+ = + 3.3 V, V- = 0 V
V
D
= V
S
= 0.3 V/3.0 V
Room
Full
± 0.02 - 1
- 50
1
50
- 1
- 5
1
5
Digital Control
Input Current, V
IN
Low I
L
V
IN(A, B, C and ENABLE)
under test = 0.6 V
Full 0.01 - 1 1 - 1 1
µA
Input Current, V
IN
High I
H
V
IN(A, B, C and ENABLE)
under test = 1.4 V
Full 0.01 - 1 1 - 1 1
Dynamic Characteristics
Transition Time
t
TRANS
R
L
= 300 , C
L
= 35 pF
see figure 1, 2, 3
Room
Full
81 172
218
172
194
ns
Enable Turn-On Time
t
ON
Room
Full
71 151
183
151
167
Enable Turn-Off Time
t
OFF
Room
Full
69 138
161
138
151
Break-Before-Make
Time Delay
t
D
Room
Full
11
Charge Injection
e
Q
V
g
= 0 V, R
g
= 0 , C
L
= 1 nF
Room 0.5 pC
Off Isolation
e
OIRR
R
L
= 50 , C
L
= 1 pF
f = 100 kHz
Room < - 90
dB
Channel-to-Channel
Crosstalk
e
X
TA LK
Room < - 90
Source Off Capacitance
e
C
S(off)
f = 1 MHz
DG4051A Room 4
pF
DG4052A Room 3
DG4053A Room 4
Drain Off Capacitance
e
C
D(off)
f = 1 MHz
DG4051A Room 14
DG4052A Room 8
DG4053A Room 5
Channel On
Capacitance
e
C
D(on)
f = 1 MHz
DG4051A Room 19
DG4052A Room 14
DG4053A Room 11
Power Supplies
Power Supply Current I+
V
IN(A, B, C and ENABLE)
= 0 V or 3 V
Room
Full
0.05 1
10
1
10
µANegative Supply Current I-
Room
Full
- 0.05 - 1
- 10
- 1
- 10
Ground Current
I
GND
Room
Full
- 0.05 - 1
- 10
- 1
- 10
