5
FN6983.1
January 14, 2010
Absolute Maximum Ratings Thermal Information
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 5.5V
Input Voltages
LIN, RIN (Note 6) . . . . . . . . . . . . . -2V to ((V
DD
) + 0.3V)
IN, CTRL (Note 6). . . . . . . . . . . .-0.3V to ((V
DD
) + 0.3V)
Output Voltages
COM-, COM+ (Note 6) . . . . . . . . . . . -2V to ((V
DD
) + 0.3V)
Continuous Current (LIN, RIN). . . . . . . . . . . . . . . .±150mA
Peak Current (LIN, RIN)
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . .±300mA
ESD Ratings:
Human Body Model
ISL54409. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5kV
ISL54410. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6kV
Machine Model
ISL54409. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250V
ISL54410. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300V
Charged Device Model . . . . . . . . . . . . . . . . . . . . . . . 2kV
Thermal Resistance (Typical) θ
JA
(°C/W) θ
JC
(°C/W)
1.8x1.4mm µTQFN (Notes 7, 8). . . 160 61.9
2mmx2mm TDFN (Notes 7, 8). . . . 84 10
Maximum Junction Temperature (Plastic Package). . . +150°C
Storage Temperature Range. . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Temperature. . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact
product reliability and result in failures not covered by warranty.
NOTES:
6. Signals on LIN, RIN, COM-, COM+, IN and CTRL exceeding VDD or GND by specified amount are clamped. Limit current to
maximum current ratings.
7. θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach”
features. See Tech Brief TB379.
8. For θ
JC
, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: V
DD
= +3.0V, GND = 0V, V
CTRL
= 1.4V, V
IN
= 0.5V,
(Notes 9, 10), Unless Otherwise Specified. Boldface limits apply over
the operating temperature range, -40°C to +85°C.
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 10, 11) TYP
MAX
(Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Input Signal Range,
V
ANALOG
V
DD
= 3.3V Full -1.5 - 1.5 V
ON-Resistance, r
ON
I
XOUT
= 40mA, V
LIN
or V
RIN
= -0.85V to
0.85V, (See Figure 2, Note 14)
+25 - 2.5 2.8 Ω
Full - - 3.8 Ω
r
ON
Flatness, r
FLAT(ON)
I
XOUT
= 40mA, V
LIN
or V
RIN
= -0.85V to
0.85V, (Notes 12, 14)
+25 - 20 60 mΩ
Full - -
70
mΩ
r
ON
Matching Between
Channels, Δr
ON
I
XOUT
= 40mA, V
LIN
or V
RIN
= Voltage at max
r
ON
over signal range of -0.85V to 0.85V,
(Notes 13, 14)
+25 - 0.1 0.32 Ω
Full - - 0.4 Ω
Active Click and Pop Shunt
Resistance
V
CTRL
= 0V, V
IN
= 0V, V
LIN
or V
RIN
= -1.5V
to 1.5V, ISL54410 only
+25 - 40 - Ω
Full - - - Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V
DD
= 2.7V, R
L
= 50Ω, C
L
= 10pF
(see Figure 1)
+25 - 5 - µs
Turn-OFF Time, t
OFF
V
DD
= 2.7V, R
L
= 50Ω, C
L
= 10pF
(see Figure 1)
+25 - 45 - ns
OFF-Isolation V
IN
= 3V, V
LIN
or V
RIN
= 0.707V
RMS,
R
L
=32Ω, f = 20Hz to 20kHz (see Figure 3)
+25 - 110 - dB
Crosstalk
RIN to LOUT, LIN to ROUT
V
CTRL
= 3.0V, V
IN
= 0V, R
L
= 32Ω, f = 20Hz
to 20kHz, V
LIN
or V
RIN
= 0.707V
RMS
(2V
P-P
),
(See Figure 4)
+25 - -90 - dB
ISL54409, ISL54410
