3
LT1220
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
t
r
, t
f
Rise Time, Fall Time A
V
= 1, 10% to 90%, 0.1V 2.5 ns
Overshoot A
V
= 1, 0.1V 5 %
Propagation Delay A
V
= 1, 50% V
IN
to 50% V
OUT
, 0.1V 4.9 ns
t
s
Settling Time 10V Step, 0.1% 75 ns
10V Step, 0.01% 95 ns
Differential Gain f = 3.58MHz, R
L
= 150Ω (Note 7) 0.10 %
f = 3.58MHz, R
L
= 1k (Note 7) 0.02 %
Differential Phase f = 3.58MHz, R
L
= 150Ω (Note 7) 0.20 DEG
f = 3.58MHz, R
L
= 1k (Note 7) 0.03 DEG
R
O
Output Resistance A
V
= 1, f = 1MHz 1 Ω
I
S
Supply Current 8 10.5 mA
ELECTRICAL CHARACTERISTICS
V
S
= ±15V, T
A
= 25°C, V
CM
= 0V, unless otherwise specified.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
OS
Input Offset Voltage (Note 4) ● 0.5 3.5 mV
Input V
OS
Drift ● 20 µV/°C
I
OS
Input Offset Current ● 100 400 nA
I
B
Input Bias Current ● 100 400 nA
CMRR Common Mode Rejection Ratio V
CM
= ±12V ● 92 114 dB
PSRR Power Supply Rejection Ratio V
S
= ±5V to ±15V ● 86 94 dB
A
VOL
Large-Signal Voltage Gain V
OUT
= ±10V, R
L
= 500Ω ● 20 50 V/mV
V
OUT
Output Swing R
L
= 500Ω ● 12 13 ±V
I
OUT
Output Current V
OUT
= ±12V ● 24 26 mA
SR Slew Rate (Note 5) ● 180 250 V/µs
I
S
Supply Current ● 811 mA
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
OS
Input Offset Voltage (Note 4) ● 0.5 4 mV
Input V
OS
Drift ● 20 µV/°C
I
OS
Input Offset Current ● 100 800 nA
I
B
Input Bias Current ● 100 1000 nA
CMRR Common Mode Rejection Ratio V
CM
= ±12V ● 92 114 dB
PSRR Power Supply Rejection Ratio V
S
= ±5V to ±15V ● 82 94 dB
A
VOL
Large-Signal Voltage Gain V
OUT
= ±10V, R
L
= 500Ω ● 550 V/mV
V
OUT
Output Swing R
L
= 500Ω ● 10 13 ±V
R
L
= 1k ● 12 13 ±V
I
OUT
Output Current V
OUT
= ±10V ● 20 26 mA
V
OUT
= ±12V ● 12 13 mA
SR Slew Rate (Note 5) ● 130 250 V/µs
I
S
Supply Current ● 811 mA
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: A heat sink may be required when the output is shorted indefinitely.
Note 3: Commercial parts are designed to operate over –40°C to 85°C, but
are not tested nor guaranteed beyond 0°C to 70°C. Industrial grade parts
specified and tested over –40°C to 85°C are available on special request.
Consult factory.
Note 4: Input offset voltage is pulse tested and is exclusive of warm-up drift.
Note 5: Slew rate is measured between ±10V on an output swing of ±12V.
Note 6: FPBW = SR/2πV
P
.
Note 7: Differential Gain and Phase are tested in A
V
= 2 with five amps in
series. Attenuators of 1/2 are used as loads (75Ω, 75Ω and 499Ω, 499Ω).
The ● denotes the specifications which apply over the temperature range 0°C ≤ T
A
≤ 70°C, otherwise specifications are at T
A
= 25°C.
V
S
= ±15V, V
CM
= 0V, unless otherwise specified.
The ● denotes the specifications which apply over the temperature range –55°C ≤ T
A
≤ 125°C, otherwise specifications are at
T
A
= 25°C. V
S
= ±15V, V
CM
= 0V, unless otherwise specified.