SPECIFICATION
MODEL
OUTPUT
VOLTAGE RANGE
Note.5
FREQUENCY RANGE
POWER FACTOR
EFFICIENCY (Typ.)
Note.7
AC CURRENT
INPUT
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
EMC IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER TEMPERATURE
OVER VOLTAGE
47 ~ 63Hz
<0.75mA / 277VAC
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 45 )
ENVIRONMENT
EMC EMISSION
SAFETY &
EMC
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
TOTAL HARMONIC DISTORTION
DC VOLTAGE
RATED CURRENT
RATED POWER
Note.5
CURRENT ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
Note.6
HOLD UP TIME (Typ.)
RIPPLE & NOISE (max.)
Note.3
VOLTAGE TOLERANCE
Note.4
CONSTANT CURRENT REGION
Note.2
OVER CURRENT
SAFETY STANDARDS
COLD START 65A(twidth= s measured at 50% Ipeak) at 230VAC550μ;Per NEMA 410
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
4 units (circuit breaker of type B) / 7 units (circuit breaker of type C) at 230VAC
(Please refer to "STATIC CHARACTERISTIC" section)
90 ~ 305VAC 127 ~ 431VDC
1. All parameters NOT specially mentioned are measured at 230VAC input, rated and 25 of ambient temperature.current ℃
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
4. Tolerance : includes set up tolerance, line regulation and load regulation.
5. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
7. The DA type power supply is less efficient than the typical efficiency in specification by 1%.
8. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
9. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently
connected to the mains.
10. This series meets the typical life expectancy of >50,000 hours of operation when Ta is about 45 or less.℃
11. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
PF 0.98/115VAC, PF 0.95/230VAC, PF 0.92/277VAC@full load≧≧≧
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
THD< 20%(@load 60%/115VC,230VAC; @load 75%/277VAC)≧≧
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
Ta=-40 ~ +45℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
2500ms, 200ms / 115VAC 500ms, 200ms / 230VAC
12ms/115VAC,230VAC
±2.0%
±0.5%
±1.0%
36V
21.6 ~ 36V
4.4A
158.4W
300mVp-p
HBG-160P-36
60V
36 ~ 60V
2.6A
156W
300mVp-p
HBG-160P-60
48V
28.8 ~ 48V
3.3A
158.4W
300mVp-p
HBG-160P-48
2.6 ~ 4.4A
1.98 ~ 3.3A
1.6 ~ 2.6A
92%
93.5%
93%
1.7A / 115VAC 0.78A / 230VAC 0.7A / 277VAC
41 ~ 47V
65 ~ 75V
54 ~ 62V
Shut down o/p voltage, recovers automatically after temperature goes down
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
195.5Khrs min. MIL-HDBK-217F (25 )℃
Refer to mechanical specification
0.4Kg; 36pcs/15.4Kg/1.35CUFT
UL8750,CSA C22.2 No.250.13-12; ENEC EN61347-1,EN61347-2-13,EN62384, GB19510.1,GB19510.14 approved,EAC TP TC 004
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
Compliance to EN55015, EN61000-3-2 Class C ( 60%) ; EN61000-3-3, GB17743, GB17625.1,EAC TP TC 020@load ≧
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547,light industry level ,EAC TP TC 020(surge immunity:Line-Earth:4KV,Line-Line:2KV)
HBG-160Pseries
160W Constant Voltage + Constant Current LED Driver
Adjustable for A-Type only (via built-in potentiometer)
Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery
DALI STANDARDS
Compliance to IEC62386-101, 102, 207 for DA-Type only
File Name:HBG-160P-SPEC 2018-03-23
