OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

PR02FS0201508KR500

P1-P3P4-P6P7-P8
PR02-FS
www.vishay.com
Vishay BCcomponents
Revision: 15-Feb-17
4
Document Number: 28915
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
FUNCTIONAL PERFORMANCE
The power that the resistor can dissipate depends on the ambient temperature.
Maximum dissipation (P
max.
) in percentage of rated power as a function of the ambient temperature (T
amb
)
Pulse performance w.r.t. IEC 61000-4-5 after 10 pulses (5 positive and 5 negative with 30 s repetition time) of 1.2/50 μs are applied
Fusing performance in response to defined overload
Ambient Temperature in °C
Power in %
050
70
100 200
Derating
-55 150
20
0
40
60
80
100
0 20 40 100806010 30 907050
100
0
200
300
400
700
500
600
Resistance in Ω
Peak Pulse Voltage in V
Overload Power in W
Maximum Fusing Time in s
2.0
0.0
4.0
6.0
8.0
18.0
10.0
12.0
14.0
16.0
10 Ω to 100 Ω
1 Ω to 8.2 Ω
907060 10080
PR02-FS
www.vishay.com
Vishay BCcomponents
Revision: 15-Feb-17
5
Document Number: 28915
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Pulse performance after a rectangular pulse of defined duration is applied
TESTS PROCEDURES AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
• IEC 60115-1, generic specification (includes tests)
The test and requirements table contains only the most
important tests. For the full test schedule refer to the
documents listed above.
The tests are carried out in accordance with IEC 60068-2-xx
test method and under standard atmospheric conditions in
accordance with IEC 60068-1, 5.3.
Climatic category LCT / UCT / 56 (rated temperature range:
lower category temperature, upper category temperature;
damp heat, steady state, test duration: 56 days) is valid.
Unless otherwise specified the following values apply:
• Temperature: 15 °C to 35 °C
• Relative humidity: 25 % to 75 %
• Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar)
For performing some of the tests, the components are
mounted on a test board in accordance with IEC 60115-1,
4.31.
In test procedures and requirements table, only the tests
and requirements are listed with reference to the relevant
clauses of IEC 60115-1 and IEC 60068-2-xx test methods.
A short description of the test procedure is also given.
Pulse Duration (s)
Peak Power in W
1
10 000
10
100
1000
10
-1
10
-3
10
-4
10
0
10
-2
10
-5
10
1
TEST PROCEDURES AND REQUIREMENTS
IEC
60115-1
CLAUSE
IEC
60068-2-
TEST
METHOD
TEST PROCEDURE
REQUIREMENTS PERMISSIBLE
CHANGE
(R
max.
)
4.4.1 - Visual examination No holes; clean surface; nodamage
4.4.2 - Dimensions (outline) Gauge (mm) SeeDimensions table
4.5 - Resistance
± 10 % R
± 20 % R
4.6.1.1 - Insulation resistance
500 V after 1min;
metal block method
R
ins min.
: 10
4
M
4.7 - Voltage proof U
ins
= 500 V
RMS
; 60 s No breakdown or flashover
4.8 -
Temperature
coefficient
At (20 / -55 / 20) °C
and (20 / 155 / 20) °C
± 250 ppm/K
4.16
21 (Ua
1
)
21 (Ub)
21 (Uc)
Robustness of
terminations
Tensile, bending, and torsion
No damage
R
max.
:± (0.5 %R +0.05)
PR02-FS
www.vishay.com
Vishay BCcomponents
Revision: 15-Feb-17
6
Document Number: 28915
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
4.17 20 (Ta) Solderability
+235°C; 2 s;
solder bath method; SnPb40
Good tinning
( 95 % covered, no visible damage)
+245°C; 3s;
solder bath method; SnAg3Cu0.5
Good tinning
( 95 % covered, no visible damage)
4.18 20 (Tb)
Resistance to
soldering heat
Unmounted components
(260 ± 5) °C; (10 ± 1) s
R
max.
:± (0.5 %R +0.05)
4.19 14 (Na)
Rapid change of
temperature
30min at -55 °C and
30min at +200 °C; 5cycles
No visual damage
R
max.
:± (1 %R +0.05)
4.20 29 (Eb) Bump 3x1500bumps in three directions; 40g
No damage
R
max.
:± (0.5 %R +0.05)
4.22 6 (Fc) Vibration
10 sweep cycles per direction;
10Hz to2000Hz;
1.5mm or 200 m/s
2
No damage
R
max.
:± (0.5 %R +0.05)
4.23 Climatic sequence:
4.23.2 2 (Bb) Dry heat 200 °C; 16 h
R
ins min.
: 10
3
M
R
max.
: ± (1.5 % R +0.1)
4.23.3 30 (Db)
Damp heat,
cyclic
55 °C; 24 h;
90 % to 100 % RH; 1 cycle
4.23.4 1 (Ab) Cold -55 °C; 2 h
4.23.5 13 (M) Low air pressure
8.5 kPa; 2 h;
15 °C to 35 °C
4.23.6 30 (Db)
Damp heat,
cyclic
55°C; 24 h;
95% to100 %RH; 5 cycles
4.24 78 (Cab)
Damp heat
(steady state)
(40± 2) °C;56days;
(93± 3 )% RH
R
max.
:± (3 %R +0.1)
4.25.1 -
Endurance
(at70 °C)
U= ;
1.5 h on; 0.5 h off; 70 °C; 1000 h
R
max.
:± (5 %R +0.1)
4.26 - Active flammability Accidental overload test
No damage,
no flaming of gauze cylinder
4.30 45 (Xa)
Solvent resistance
for marking
Isopropyl alcohol (used in industrial application)
+23 °C; toothbrush method
Marking legible; no visible damage
4.35 - Passive flammability Needle flame test
No ignition of product,
no ignition of under layer
burning time is less than 30 s
TEST PROCEDURES AND REQUIREMENTS
IEC
60115-1
CLAUSE
IEC
60068-2-
TEST
METHOD
TEST PROCEDURE
REQUIREMENTS PERMISSIBLE
CHANGE
(R
max.
)
P
70
x R
P1-P3P4-P6P7-P8

PR02FS0201508KR500

Mfr. #:
Buy PR02FS0201508KR500
Manufacturer:
Description:
Metal Film Resistors - Through Hole 2watt 1.5ohms 10% Fusible NonInductive
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet