OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

2320157

P1-P3P4-P6P7-P9P10-P10
QUINT-DIODE/12-24DC/2X20/1X40
104690_en_00 PHOENIX CONTACT 4
Ambient conditions
Ambient temperature (operation) -40 °C ... 70 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Max. permissible relative humidity (operation) ≤ 95 % (at 25 °C, no condensation)
Vibration (operation) < 15 Hz, amplitude ±2.5 mm in acc. with IEC 60068-2-6
15 Hz ... 150 Hz, 2.3g, 90 min.
Shock 30g in all directions in acc. with IEC 60068-2-27
Pollution degree in acc. with EN 50178 2
Climatic class 3K3 (in acc. with EN 60721)
Approvals
ATEX II 3G Ex nA IIC T4 Gc
KEMA 10 ATEX 0165X
IECEx Ex nA IIC T4 Gc
IECEx KEM 10.0091
UL approvals UL/C-UL listed UL 508
UL/C-UL Recognized UL 60950
UL/C-UL listed ANSI/ISA 12.12.01
Conformance with EMC Directive 2004/108/EC
Noise immunity according to EN 61000-6-2
Electrostatic discharge EN 61000-4-2
Housing Level 4
Contact discharge 8 kV (Contact discharge)
Discharge in air 15 kV (Air discharge)
Comments Criterion A
Electromagnetic HF field EN 61000-4-3
Housing Level 3
Frequency range 80 MHz ... 1 GHz
Frequency range 1 GHz ... 3 GHz
Comments Criterion A
Fast transients (burst) EN 61000-4-4
Input 2 kV (level 3 - asymmetrical: conductor to ground)
Output 2 kV (level 3 - asymmetrical: conductor to ground)
Comments Criterion A
Surge current loads (surge) EN 61000-4-5
Input 2 kV (level 3 - asymmetrical: conductor to ground)
1 kV (Level 2 - symmetrical: Conductor to conductor)
Output 2 kV (level 3 - asymmetrical: conductor to ground)
1 kV (Level 2 - symmetrical: Conductor to conductor)
Comments Criterion A
Conducted interference EN 61000-4-6
Input/output Level 3
Frequency range 150 kHz ... 80 MHz
Comments Criterion A
Emitted interference in acc. with EN 61000-6-3
Radio interference voltage in acc. with EN 55011 EN 55011 (EN 55022) Class B, area of application: Industry and residential
Emitted radio interference in acc. with EN 55011 EN 55011 (EN 55022) Class B, area of application: Industry and residential
QUINT-DIODE/12-24DC/2X20/1X40
104690_en_00 PHOENIX CONTACT 5
5 Safety regulations and installation notes
DANGER
Never carry out work when voltage is present.
CAUTION:
Before startup please ensure:
All feed lines are sufficiently protected and di-
mensioned!
All output lines are dimensioned according to
the maximum output current of the device or
separately protected!
Sufficient convection must be guaranteed.
Do not exceed max. input/output current of
60A. Use current-limited source, e. g., QUINT
POWER or suitable fuse.
The connection must be carried out by a com-
petent person and protection against electric
shock guaranteed.
The redundancy module is a device installing
into an enclosed space. Installation and startup
may only be carried out by qualified personnel.
The relevant country-specific regulations must
be observed.
Observe mechanical and thermal limits.
The redundancy module is maintenance-free.
Repairs may only be carried out by the manu-
facturer.
CAUTION:
Installation in zone 2
Observe the specified conditions for use in po-
tentially explosive areas.
Install the device in a suitable approved hous-
ing (with at least IP54 protection) that meets the
requirements of EN60079-15.
The device is not designed for use in potentially
dust-explosive atmospheres. If dust is present,
install the device in suitable, approved housing.
The device must be stopped and immediately
removed from the Ex area if it is damaged or
was subject to an impermissible load or stored
incorrectly or if it malfunctions.
The device is designed for installation in zone 2
potentially explosive areas according to Direc-
tive 94/4/EC.
Within a potentially explosive area, the redun-
dancy module is to be connected to the equipo-
tential bonding system via a 35mm DIN rail
(EN60175) rail
QUINT-DIODE/12-24DC/2X20/1X40
104690_en_00 PHOENIX CONTACT 6
6 Structure
Figure 1 Function elements
1 IN1/IN2 DC input:
2...24V input voltage, I
N
=2 x20A
2 DC output
3 Universal snap-on foot: 35mm DIN rails according to
EN60715 and panel mounting with UWA182/52
7 Installation
Figure 2 Convection
+
+
–
–
+
–
–
+
Output DC 40A
Input DC 12-24V 2x20A
IN
1 IN2
QUINT DIODE
1
2
3
In order to ensure sufficient convection, we rec-
ommend a minimum vertical distance of 50 m
to the other modules. A lateral distance of 5
mm, and in the case of active components, that
of 15 mm is necessary for proper functioning of
the module.
Depending on the ambient temperature and
the load of the module, the housing can be-
come very hot!
The module can be snapped onto all DIN rails
according to EN60715 and must be mounted
horizontally (connecting terminal blocks on top
and bottom).
+
+
–
–
+
–
–
+
O
u
tp
u
t
D
C
4
0
A
In
p
u
t
D
C
1
2
-2
4
V
2
x
2
0
A
IN
1
IN
2
QUINT DIODE
P1-P3P4-P6P7-P9P10-P10

2320157

Mfr. #:
Buy 2320157
Manufacturer:
Phoenix Contact
Description:
Non-Isolated DC/DC Converters QUINT-DIODE/ 12-24DC/2X20/1X40
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet