OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

NFM21CC221R1H3D

P1-P3P4-P6P7-P9P10-P10
NFM21CC221R1H3_ (0805, 220pF, DC50V)
_: packaging code Reference Sheet
1.Scope
　　
2.MURATA Part NO. System
(Ex.)
3. Type & Dimensions
a)Equivalent Circuit
(Unit:mm)
4.Rated value
5.Package
Product specifications in this catalog are as of Mar.3,2016,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
Insulation
Resistance
mark
Packaging Unit
(7) Packaging
This product specification is applied to Chip EMIFIL®Chip 3-terminal Capacitor used for General Electronic equipment.
(3) Nominal
Capacitance
Capacitance
Tolerance
(5)
DC Rated
Voltage
Rated
Current
(mA)
j
0.2+0.2/-0.1
Chip EMIFIL®Chip 3-terminal Capacitor for General
Specifications and Test Methods
(Operating /Storage Temp. Range)
-55 to 125 °C / -55 to 125 °C
±20 %
700mA(DC)
300mΩmax.
220 pF
DC
Resistance
1000MΩmin.
DC 50 V
(1)-2 W
T
e
g
D
f180mm Reel
PAPER W8P4
4000 pcs./Reel
1.25±0.1
0.85±0.1
0.3±0.2
0.2 min.
(1)L/W
Dimensions
(2)Features
(3)Nominal
Capacitance
(4)Temperature
Characteristics
(5)DC Rated
Voltage
(6)Electrode
(7)Packaging
Code
NFM 21 CC 221 R 1H 3 D
NFM21CC221R1H3-01 1
Electrical Performance
No Specification Test Method
1 Capacitance Shown in Rated value.
Frequency
(Cap.)
22 to 100pF : 1±0.1MHz
220 to 22000pF : 1±0.1kHz
Voltage : 1±0.2V(rms)
2
Voltage : Rated Voltage
Time : 2 minutes max.
3 DC Resistance Measured with 100mA max.
(Rdc1,2) Rdc1 : between signal terminals
Rdc2 : between ground terminals
4 Withstanding Voltage Products shall not be damaged.
Test Voltage : 150V(DC)
Time : 1 to 5 s
Charge Current : 50 mA max.
5
Operating Temperature
Shown in Rated value. Includes self-heating
6
Storage Temperature
Standard Testing Condition
< Unless otherwise specified >
< In case of doubt >
Temperature : Ordinary Temp. / 15 °C to 35 °C Temperature: 20 °C ± 2 °C
Humidity: Ordinary Humidity / 25 %(RH) to 85 %(RH)
Humidity: 60 %(RH) to 70 %(RH)
Atmospheric pressure: 86 kPa to 106 kPa
■SPECIFICATIONS AND TEST METHODS
Item
Insulation
Resistance(I.R.)
Rdc2
Rdc1
Rdc1
Rdc2
JEMCPS-02213C 2
Mechanical Performance
No Specification Test Method
1 Appearance and
Appearance:No defects or abnormalities. Appearance:Visual inspection.
Dimensions
Dimensions:Within the specified dimensions. Dimensions:Using calipers.
2 Solderability Flux : Ethanol solution of rosin, 25(wt)%
Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 240 ± 3°C
Immersion Time : 3±1 s
Immersion and emersion rates : 25mm / s
3 Resistance to
Meet Table 1. Flux : Ethanol solution of rosin, 25(wt)%
soldering heat
Table 1 Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 270 ± 5°C
Immersion Time : 10 ± 1 s
Immersion and emersion rates : 25mm / s
Initial values : About 220 to 22000pF,
measured after heat treatment (150+0 / -10 °C,1hour) and
exposure in the room condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
　　　　　　22 to 100pF : 24±2 hours
　　　　　　220 to 22000pF : 48±4 hours
4 Bending Strength
Meet Table 2. It shall be soldered on the glass-epoxy substrate(t = 1.0mm).
Table 2 Deflection : 2 mm
Keeping Time : 30 s
(in mm)
5 Drop
It shall be dropped on concrete or steel board.
Method : Free fall
Height : 75 cm
Attitude from which the product is dropped : 3 directions
6 Bonding Strength
It shall be soldered on the glass-epoxy substrate.
Applying Force (F) : 9.8 N
Applying Time : 30 s
(in mm)
7 Vibration Meet Table 3.
It shall be soldered on the glass-epoxy substrate.
Table 3 Oscillation Frequency : 10 to 55 to 10Hz for
1 minute
Double Amplitude : 1.5 mm
Time : A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hours)
Preconditioning : About 220 to 22000pF,
heat treatment (150+0 / -10 °C,1hour)
■SPECIFICATIONS AND TEST METHODS
Item
The electrodes shall be no failure after tested.
Products shall be no failure after tested.
Electrodes shall be at least 90% covered with
new solder coating.
The Number of Time : 3 times for each direction
(Total 9 times)
45
R230
F
Deflection
45
Product
Pressure jig
0.6
0.8
1.6
1.0
Appearance
No damaged
Cap. Change
Within ±7.5%
I.R.
Meet the initial rated value.
Rdc 1,2
22 to 2200pF
0.5 max.
22000pF
0.05 max.
Appearance
No damaged
Cap. Change
Within ±12.5%
Rdc 1,2
22 to 2200pF
0.5 max.
22000pF
0.05 max.
Appearance
No damaged
Capacitance
Meet the initial rated value.
Rdc 1,2
22 to 2200pF
0.5 max.
22000pF
0.05 max.
JEMCPS-02213C 3
P1-P3P4-P6P7-P9P10-P10

NFM21CC221R1H3D

Mfr. #:
Buy NFM21CC221R1H3D
Manufacturer:
Description:
Feed Through Capacitors 220pF 50V 700mA
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet